Jump to content
SAU Community

Recommended Posts

under pressure yes, once the tyre is deflated you can get them off easily and safely. Learnt how to do it on many an army truck when we did our driver's courses. Inflation is always face down or in a cage just in case it springs off

Front 215/45/17 Tyres - Something reasonable quality

Rear 235/45/17 Tyres - Anything above 50%

R32 Roof lining

R32/R33/R34/S13/S14/S15 Steering rack bushes to hold the rack in

Anybody have a press I could borrow for 5 minutes? Just need to press 2 items which are already off the car.

Front 215/45/17 Tyres - Something reasonable quality

Rear 235/45/17 Tyres - Anything above 50%

R32 Roof lining

R32/R33/R34/S13/S14/S15 Steering rack bushes to hold the rack in

Anybody have a press I could borrow for 5 minutes? Just need to press 2 items which are already off the car.

How soon do you need rack bushings ? I have superpro kit to fit so my factory ones are coming off ? Low km r34

R32 actuator

R33 Series 2 driver side seat(without rips)

R33 2 door driver side A trim panel(without holes or speaker boxes)(dark grey/black)

R33 std Cat converter splash guard(guard only)

R33 floor mats(must be good cond)

R33 camber kit(front or rear)

R33 series 2 GTst aftermarket computer ECU

PM me

Edited by cosworth1971

WTB R33 GTR Skyline Cluster that says 320kms...or a cheap stock R33 gtst one...mine as stopped working..plz PM me if you got one for sale Thanks

i have R33 gtr cluster with the standard 180 on clock but also have the 300kph Nismo add in speedo stuff in the for sale section

WTB: R32 non-turbo

Looking for a P-plater mate, so he wants a non-turbo R32. Would prefer 2 door, but will consider 4 door.

Local (Adelaide) or interstate is fine.

About to hit up the classifieds to look for one, but figured I'd ask here for a quick referal.

;)

PM me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...