Jump to content
SAU Community

A31/r32 Loom Swap Q's

Hella Flush

By Hella Flush,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Hella Flush Experienced

Hella Flush

Posted
Posted

herro

im not one for racing but could not resist seeing what the new rb20de cef does compared to what im used to with my old rb20det one...

bad idea

owned by a mildly modded rb20det r31 which even worse had custom plates with the owners name...

this cannot happen and i appologise to all cef dawg owners...

engine out of the blue one is gonna go into the black one next weekend ive decided and ill sell the blue one with rb20de...

my question... loom swap... i wanna put 32 loom in as its a 32 20 with half cut a31 half cut r32 loom bits in it... just want a fresh hassle free full 32 loom to go in...

straight forward rip out and put in? use 32 comp and everything... im assuming so but thought i would ask!

told the mrs tonite - next weekend is dedicated cef weekend

engine out of the blue one and tidy blue one up

black one gets the pink bits cradle with 32 5stud hubs, r33 twin pots and kaaz 2way + solid cradle spacers and gtr sway bar

then weekend after - turbo engine can go in

Link to comment
https://www.sau.com.au/forums/topic/143917-a31r32-loom-swap-qs/
Share on other sites
huddy Veteran

huddy

Posted
Posted

ADZ, if changing looms, you may need to change everything else to suit. i know that cefiro has 'square' style connectors (eg z32 afm fits straight in with same pinouts!) and 32 has round ones....

this may be a problem with all your other connections for water temp sender etc... i know coilpacks are ok, and inj are ok, but at the other end where they go into ignitor pack are no good.

so unless you have got all the bits, i wouldnt bother.

On another note i've had 2 different 32 remaps working in my car before, they were just not a suitable map (one was kelly's and other was a donnon one).

Hella Flush Experienced

Hella Flush

Posted
  • Author
Posted

yeah way i see it huddymonster

i have an r32 rb20det... so if i use full r32 rb20det engine harness all wires should be fine... my only problem would be connecting to the chassis loom (dash cluster etc) which may require few wires to be cut?

agreed?

robots Experienced

robots

Posted
Posted (edited)

$350 aint that expensive. )) Some koom conversions are much more expensive )).

Anyway what I wanted to ask is, if any of you guys know if the procedure will be similiar to this if the base car is rb24s ceffy (carb one). It doesn't have an ecu and fuel pump is retarded and bucn of other 19th centurey crap LOL.

Edited by robots

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • MBS206
      What should I do next to hold the head on

      By MBS206 · Posted

      When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

    • Rezz
      Chris' Toyota Mark ii JZX110

      By Rezz · Posted

      Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...