Jump to content
SAU Community

Recommended Posts

Rocker cover gasket change in a series 1 R33 GTS-T (RB25DET):

Disclaimer:

Do this at your own risk! I accept not responsibility for injury or damage to any part of the engine or otherwise as a result of following this guide.

For Torque specs and other specific instructions, see the bottom of this post.

What you will definitely need:

New gasket(s) from nissan

New rear cam-shaft seal(s) from nissan

Gasket goo

Large phillips-head screwdriver

Medium phillips-head screwdriver

Spanner set

Socket set

Allan key set

Around an hour - more if it's your first time.

What you don't need but should probably use:

Carby cleaner

Relatively clean rags/towels

Throttle body gasket

1. Go to Nissan and purchase the rocker cover gasket(s) you require. This guide goes through the process of replacing both.

Part numbers for RB25DET:

LEFT (exhaust side) gasket: 13270-58S01

RIGHT (inlet side) gasket: 13270-58S11

(Consult your nissan dealer to be SURE of this. I am fairly confident that I have left & right correct. I bought both for $72.05.)

rightgasket.jpg

leftgasket.jpg

'Half moon' Cam gear seals: 11051-58S00

crankseals.jpg

crankseals2.jpg

2. Pop the bonnet.

3. Remove the crossover pipe.

There are a number of things that you must disconnect/unscrew to fully remove the crossover pipe and associated bits and pieces. These are highlighted in red on the image below.

enginecloseupred.jpg

It would be worthwhile putting a clean cloth in either end of the crossover now that it is removed, and also in the throttle body to prevent any unwanted debris entering the engine.

4. Now remove the two hoses on the rocker cover breather:

nocrossoverred1.jpg

Mine split when removing as they are very stiff hoses. I will need to get new ones from Nissan and I will update this with part numbers when I do.

5. Remove the coilpack cover.

Disconnect the two connectors highlighted in red below, and then use the appropriate Allan key to remove the 8 screws holding the coilpack cover to the rocker covers (highlighted in blue)

nocrossoverred2.jpg

6. Unscrew the left rocker cover

Take particular note on how tightly these screws are done up: NOT VERY TIGHTLY AT ALL. Remember not to do them up very tight when you put the cover back on. just to the point where u can see the rubber washer undergo a bit of pressure. Torque specs are at the bottom of this post.

Also, on some screws the rubber grommet will also come out with the screw, on others it will not. Do not lose these grommets!

Be very careful not to let any dirt or other crap into the engine, or into the rocker cover.

The 10 screws are highlighted on the image below (right hand side not visible)

nocoilcoverred.jpg

Removing the rocker cover will now expose your camshaft:

leftcoveroff.jpg

7. Remove the old gasket from the rocker cover, and replace with the new one.

Use gasket goo or sealant on the raised half circle on the front side of the cover, highlighted below:

leftcoverred.jpg

While I had the cover off, I cleaned the outside with Carby cleaner, being extra careful not to get any inside the cover.

Use a pair of needle-nose pliers to gently lift the old half-moon rubber from the back of the rocker assembly (highlighted in red below). Coat all outside edges of the new half-moon with gasket goo, and then reinsert it.

oldseal.jpg

8. Replace the left rocker cover by replacing the screws

Remember, not too tight at all.

The process for removing the right cover is slightly different:

9. Remove the screws on the right of the cover.

Note that there is also smaller screws that need to be removed, that are currently supporting the wires:

screwred.jpg

Either that or unfold the support and remove the wires. I did it the hard way.

10. Remove the screws on the left of the cover.

Removing the screws on the left of the cover is more tricky. If you have an angled screwdriver, go for it right now! If not (I didn't) you will need to unbolt the throttle body assembly.

There are 4 bolts you need to undo. well, actually two nuts on the top, and two bolts below.

The top two nuts can be done with a spanner. Use sockets for the bottom bolts, as if you use a spanner you will need to remove the Throttle Position Sensor.

Once the TB is unbolted, unhook the throttle cable from it's position and carefully lift the TB out of the way, allowing you access to the rocker cover screw beneath.

The gasket may break in this step, so it would be handy to replace it while you are doing this. I didn't have to, but probably should have :)

Throttle body and throttle cable (red) and TPS (blue):

plenumred.jpg

The top screw is tricky, but just involves holding a lot of stuff out of the way to get to it. Magnetic screwdrivers work well here.

11. Repeat steps 7 & 8 for this side, and then perform steps 10, 5, 4 & 3 in reverse order.

If putting the allan key screws back on the coilpack cover is proving difficult, try tightening the inner screws of both rocker covers just a little to bring them closer together.

Make sure everything that was disconnected is now properly reconnected, and all hose clamps are tight.

And you're done:

finished.jpg

12. Start 'er up!

An abridged (but specific) guide from a workshop manual is as follows:

rocker1.JPG

rocker2.JPG

rocker3.JPG

Hope this helps :(

Edited by Mike_
Link to comment
https://www.sau.com.au/forums/topic/144235-changing-the-rocker-cover-gasket/
Share on other sites

Co-incidentally I have just done this today!

I don't see any mention of the half-moon rubbers that should really be replaced. You highlighted and said to put goo around that area, which is correct. (or goo the half-moons before you put them in).

Anyhoo, they're a seperate part number, and apparently these motors leak from there before they leak from the gasket, so while you're already there:

7. use a pair of needle-nose pliers to gently lift the old half-moon rubber from the back of the rocker assembly. Coat all outside edges of the new half-moon with gasket goo before reinserting.

Edited by RANDY

I don't remember seeing any half moons aside from the raised half circle part of the gasket itself...

I'm not too familiar with mechanics in general but I know enough to get me by, so it's likely that I missed this.

Can you give me any photos of what you're referring to?

the rear camshaft seals is what he means. Half moon that slips in the back half moon cutout...but by the sounds of it the new rocker cover seals have them built in now. Good idea nissan!

Nope! I can see the gasket pics, and they don't have the half-moon built in. They ARE a different part number, and I had to ask for them seperately. I bought mine 2 days ago now, and they weren't built-in.

So you guys above who say you can see it built-in, that raised arch is for the front, but the rear camshaft seals (half-moon) can come out. When in, it makes the back flat, which sits flat against the flat part of the rocker gasket/cover.

I didn't take pics, but next time someone is doing this, they will be able to see what i'm talking about... as R33_racer mentions also.

So if you're still leaking oil around the back, and down onto your gearbox, those half-moons will need to be replaced and resealed! =-]

  • 4 years later...

just about to do this job n have a query for those out there that have done it...

some of the little rubber grommets that sit under the screws around the end of the cam cover n hold it down look pretty perished on mine.

are these something that also needs to hold an oil seal and therefor need to be in good condition or what?

n if they do need to be in decent condition are they just a standard grommet or are they something im going to need to source the specific OEM part for?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...