Jump to content
SAU Community

Recommended Posts

Does anyone have any idea where I could find the paint code for the stock nissan 180sx purple paint.

the180purple.jpg

Although purple 180s seem very different colours in different pictures depending on lighting this i am fairly sure is not the right colour.

This is advertised as pearl but i'm fairly sure is the right stock colour.

post-3511-1152459204.jpg

http://ausdrift.com/gooch180sx.asp

This car is definately the right colour.

I need someone who has this colour to read the nissan information plate which looks something like:

.................Nissan Motor Co LTD Japan

............................E-HCR43

Chassis No: HCR32-016693

Model: RCR32GASM AA

Colour code: KG1 G 130

Engine: RB20DET 1998 cc

Transmission / Axle : RE4R01A RC43

And tell me what their "Colour code: KG1 G 130" says.

So far one person has quoted it as LN1 which doesn't seem to make sense given that matches with 'Concord Grey'.

Edited by Sarumatix

It is 100% a stock colour :happy: know several people who have the colour.. comes on later model 180sx :). I don't doubt the color is in the paintcode thread.. but how the heck do I find out what the name of the color actually is?

Edited by Sarumatix
  • 2 weeks later...

KK I have determined that the SAU paint code list is quite short for silvias :miner:. LP2 red/blue pearl is the 180sx type-x purple, from simple deduction the only other purple paintcode which was around during the right time frame is LP1, grey/purple. The name sounds right but I can't find any conclusive evidence that this is the right code, can anyone point me towards enlightenment?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...