Jump to content
SAU Community

Help Diagnosing Dead Thermostat

wilch

By wilch,
in General Maintenance

 Share

Recommended Posts

wilch Grand Master

wilch

Posted
Posted

Hey guys,

Here's the jist:

R32 GTST RB20det

Appears to be overheating. Thermofan turns on and can hear it above 3000rpm sometimes....And it's happening more frequently as the weather is getting hotter.

Only use to do it sometimes.

Now does it all the time.

Anyway, I just took it for a drive to warm everything up and to test the new fuel pump. Came back home and opened the bonnet.

Touched the top radiator hose, was hot to the touch.

Touched the bottom radiator hose near the block, and it was cold to the touch.

Now this bottom hose is where the thermostat is.

Am I right in thinking that because the top one is hot, and the bottom one (where the thermostat is) is cold, that the thermostat is broken in the closed position?

Cheers,

wil..

Link to comment
https://www.sau.com.au/forums/topic/145314-help-diagnosing-dead-thermostat/
Share on other sites
GoldZilla Grand Master

GoldZilla

Posted
Posted
Thermostate is jammed closed.

Remove it throw it into boiling water to see if it opens then replace it cause it won't open.

Oh yeah, forgot about that testing trick - my old man used to do that!

mad082 Grand Master

mad082

Posted
Posted

the bottom hose (cold one) is where the water goes into the motor. the top (hot) hose is where the water comes out of the head. so the top hose should be hotter than the bottom one. that is why that is where to temp sensor is. so that it reads the hottest temp the water gets to.

do you have a fmic? if you do then that won't be helping as it slows a lot of air going through the radiator.

wilch Grand Master

wilch

Posted
  • Author
Posted

The 32 is stock.

Hmmm...I was lead to believe that the bottom hose is where the thermostat is. It's cold, and it shouldn't be when the top one is hot.

(photo of upside down engine courtesy of mr32)

DSC00084.jpg

  • 2 weeks later...
Doctor 30 Community Regular

Doctor 30

Posted
Posted

I have the same problem but my thermostat opens in boiling water. I heard that if if doesn't open on boiling water it is definitely stuffed. But if it does open it doesn't necessarily mean it is good because it is a totally different enviroment under pressure.

Can anyone confirm if I am right or wrong in thinking this?

Duncan Grand Master

Duncan

Posted
Posted

isn't a thermostate $20 at your local repco? just grab one and a gasket and change it :ninja:

if you really want to check the boiling water trick you need a temp gauge in it as well make sure it opens at the right temp 76o for GTR not sure if gtst is the same

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...