Jump to content
SAU Community

Recommended Posts

Guys,

I've gone in a new direction with my car so I have my HKS 2530's with actuators (done about 10,000kms - still perfect) and my Power FC with the hand controller for sale.

Won't seperate the turbo's or the Hand Controller from the Power FC.

Turbo's - $2,700

Power FC + HC - SOLD

Contact me via PM or on 0419 375 140.

Cheers

Snowy.

post-5136-1166391454.jpg

Link to comment
https://www.sau.com.au/forums/topic/146351-twin-hks-2530s-power-fc/
Share on other sites

The last tune done on my car with the power fc was 362rwkw's @ 24psi that was also with the 2530's, cams and a bottom end (pistons only).

Before I did the bottom end I was making 325rwkw's @ 19psi with the power fc, cam gears and 2530's.

So do you want your stock turbos back for the "new direction" mate?

Discovered it wasn't them at all but a machine shop not fitting the pistons to spec so the rings failed. Plus I have other turbos to use now.

Anyway I hope the sale goes off before Xmas so you can buy new goodies.

Hey Geoff,

Na I'm going the N1's route so I can make the car Targa Spec. It's going to suck at first as I know I'm going to miss the top end pull of the 2530's but the rules are rules and there is nothing much I can do about it if I want to start competing in some of these big events.

Targa it is then. Excellent. What about the Garrett GTSS spec turbos? Look the same as stock and 320awkw. Not called Targa cheaters for nothing.....

Everything is now back on the market as the previous buyers have had to pull out.

I've attached a copy of my last dyno graph taken in March this year when I had both the power fc and 2530's in the car. This should clear up any questions on power and response of these turbos.

  • 3 weeks later...
  • 5 weeks later...
  • 3 weeks later...
  • 3 weeks later...
R32 GTR the rules are M2 spec in the cams tarmac rally regs. Think 99% dead standard. http://www.cams.com.au/downloads/articles/...ions%202006.pdf

that link is for pre 1982 vehicles, thanks all the same. I'll dig around the cams site to see if i can find the after 1982 one lol

  • 4 weeks later...
  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...