Jump to content
SAU Community

Hks Ssqv Stalling Problem

Mid_Nite_R33

By Mid_Nite_R33,
in Engines & Forced Induction

 Share

Recommended Posts

Mid_Nite_R33 Mentor

Mid_Nite_R33

Posted
Posted

hey guys,

Just fitted my universal hks ssqv onto an adaptor that I got made up for me. Having many issues, car idles horrible, up and down like crazy from like 100 to 1000 rpm non stop, engine struggles and vibrates weird, while its doing that black smoke comes out of the exhaust, If i put my hand on the bov where it blows the air out the rev thing stabilizes but as soon as you drive again its doing it all again. I have blocked off the plumback pipe with a bottle cap, is that good enough? It had an O ring that i purchased from US which is too small and doesnt hold it tight so I have put a larger O ring to make it all sit firm yet under mild acceleration you can hear the bov wooshing(leaking air right?)

Since then I have out my stock bov back on and now my car has misfires on high rpm

Can anyone help me with this?

thanks heaps

Link to comment
https://www.sau.com.au/forums/topic/146571-hks-ssqv-stalling-problem/
Share on other sites
RB20JT Rising Star

RB20JT

Posted
Posted

yer i had the same problem...i just took it off and pout the stocker back on. thing is i noticed that the aftermarket bov didnt properly close when the butterfly was closed, like i revv the motor, it opens but closes slowly but not fully...im assuming its a faulty bov or i have a vaccum leak where I HAVE NO CLUE!!!

Mid_Nite_R33 Mentor

Mid_Nite_R33

Posted
  • Author
Posted

yea it seems to leak, but thing is i put the stocker back on and now my car misfores on high rpm when flat out, would it be coz the black smoke covered the plugs and they are no good? or is it coil packs which i doubt could be damaged by playing around with a bov.

cameron Mentor

cameron

Posted
Posted

2nd one I've seen play up... The valve c*cks sideways and gets jamed open = leak...

You should be able to close and you will hear it pop back into its place. It will work perfectly intil it gets jamed again.

Yeah as other said change plugs, because when the BOV is leaking its the same as intercooler pipe blown off and AFM reads all this Air coming in but its not actually getting into the engine... rich rich mixtures.

Mid_Nite_R33 Mentor

Mid_Nite_R33

Posted
  • Author
Posted

yeah i have a genuwine universal hks ssqv bov, im just gonna sell this one and buy a skyline specific hks ssqv which are not meant to have adjustment screw, is that right?

the rich mixtures must have stuffed my plugs, i'll replace the plugs on monday and reset my ecu and see how it goes.

Btw i had the car running with this dodgey bov for about 20 mins blowing black smoke while it was reving like crazy, would it damage my airflow meter by any chance?

gt-t_r34 Mentor

gt-t_r34

Posted
Posted
yeah i have a genuwine universal hks ssqv bov, im just gonna sell this one and buy a skyline specific hks ssqv which are not meant to have adjustment screw, is that right?

the rich mixtures must have stuffed my plugs, i'll replace the plugs on monday and reset my ecu and see how it goes.

Btw i had the car running with this dodgey bov for about 20 mins blowing black smoke while it was reving like crazy, would it damage my airflow meter by any chance?

wouldnt hurt to clean the afm anyway with some throttle body cleaner its not hard to do. im not sure about the car specific model having no adjustment screw, because all cars vary, like say you might have a standard car and it works fine on it and then you might have the same model car but with 300kw it want hold boost there or it will cause excess flutter/not open on the stanard car. i reckon the best bov you can get it the new greddy type rs it can be plumb back aswell. :P

Mid_Nite_R33 Mentor

Mid_Nite_R33

Posted
  • Author
Posted
wouldnt hurt to clean the afm anyway with some throttle body cleaner its not hard to do. im not sure about the car specific model having no adjustment screw, because all cars vary, like say you might have a standard car and it works fine on it and then you might have the same model car but with 300kw it want hold boost there or it will cause excess flutter/not open on the stanard car. i reckon the best bov you can get it the new greddy type rs it can be plumb back aswell. :P

how do you clean the airflow meter? pull it apart or something?

Mid_Nite_R33 Mentor

Mid_Nite_R33

Posted
  • Author
Posted
wouldnt hurt to clean the afm anyway with some throttle body cleaner its not hard to do. im not sure about the car specific model having no adjustment screw, because all cars vary, like say you might have a standard car and it works fine on it and then you might have the same model car but with 300kw it want hold boost there or it will cause excess flutter/not open on the stanard car. i reckon the best bov you can get it the new greddy type rs it can be plumb back aswell. :P

Why do you say the greddy type rs is the best?

what sound does it make? is it like a unique sound or the usual pccchhh! ?

hayden49 Rising Star

hayden49

Posted
Posted

Better yet, keep your original BOV and eliminate all your problems.

Personally id rather my car run properly then have a full sick phhhs phss whistle whistle where are the chicks? sound.

My car came with a turbo smart plum back bov but if i didnt i wouldnt have bothered spending that much to replace something that already works just fine.

Mid_Nite_R33 Mentor

Mid_Nite_R33

Posted
  • Author
Posted
Better yet, keep your original BOV and eliminate all your problems.

Personally id rather my car run properly then have a full sick phhhs phss whistle whistle where are the chicks? sound.

My car came with a turbo smart plum back bov but if i didnt i wouldnt have bothered spending that much to replace something that already works just fine.

thats true, but once you boost your car the stock bov doesnt hold boost and leak bad, so you have to have something aftermarket on a modded car

Mid_Nite_R33 Mentor

Mid_Nite_R33

Posted
  • Author
Posted
Well if you NEED to, go a plum back dude, i havnt had a problem with my bov at all, no idling issues or stalling.

If you have the standard ECU definately go plumb back.

yea thats my plan, either plumback the hks ssqv or get this greddy type RS and plumb it back

gt-t_r34 Mentor

gt-t_r34

Posted
Posted

the greddy rs you can either plumb back or atmo, better than other bovs that do both.

you clean the afm with throttle body cleaner just spray it let it dry and then spray it again and it takes the dirt off pretty easy!

go to nengun for the greddy type rs they have cheap prices and vechile specific models.

Rolls Grand Master

Rolls

Posted
Posted
yea thats my plan, either plumback the hks ssqv or get this greddy type RS and plumb it back

Youll still be able to hear them if you plumb them back as well, so you can get the best of both worlds (that is if you like the noise of a bov)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Roy
      Ben's R32 Gtst Build

      By Roy · Posted

      Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • GTSBoy
      Another little story of weird shit happening

      By GTSBoy · Posted

      Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • MBS206
      Another little story of weird shit happening

      By MBS206 · Posted

      Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Shizu
      Returning after a long time!

      By Shizu · Posted

      Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • dbm7
      Looking for a part number for this part here

      By dbm7 · Posted

      Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...