Jump to content
SAU Community

Recommended Posts

ey guys,

did a compression test today, however, i disconnnected every hose when i removed the intake manifold and removed all the spark plugs, then i performed the compression test.

Cylinder:

1. 146 PSI

2. 145 PSI

3. 147 PSI

4. 145 PSI

5. 146 PSI

6. 145 PSI

i dunno wat the go is.. And is this the way u do a compression test or not? by removing all park plugs and then cranking it?

Link to comment
https://www.sau.com.au/forums/topic/146595-compression-test-for-rb20det/
Share on other sites

ok....so keep all plugs in, take one out, test it, then put it back it, then take the next one out and test it yer? do i loost compression when all spark plugs r out? coz i just cranked it till it popped...

Depends on how your gauge reads dude. A lot of low qual gauges about that read way off.

Also rb20 donk is fairly low comp I'd expect 130 - 150.

You look more for variation. The readings on your engine are awesome !!

around 150psi is normal for the age the engine,manual specifies 170psi with the limit value (lowest) 128psi, the variance limit shouldnt be more than 14psi beween cylinders

u should have the engine close to operating temp at least, remove ALL plugs, attach gauge to cylinder (screw fitting is the better ones), depress pedal FULLY u must have WOT, crank till needle stops moving which should be about 7 engine revolutions, then record ur readings,

urs seem good not much variation which is good

im not sure if the readings will be lower or higher when stone cold as i have only done it when at operating temp.

maybe someone can verify that as my engine is not finished yet to be running

cheers,

brad

Edited by RB20/30Det_VL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...