Jump to content
SAU Community

Recommended Posts

I have a problem with my air con, it only blows out cold air when set at 18 degress. As soon as you adjust the temperature to 18.5 or above it changes to the heater setting. It stops blowing out cold air and starts to blow out warm air.

Has any one had this problem before? know what is causing it? or knows how to help? :action-smiley-069:

Link to comment
https://www.sau.com.au/forums/topic/146646-r34-air-con-problem/
Share on other sites

Ok....hope this helps...I had the exact same problem..cold air at 18...then when 18.5 or 19 onwards it gets warm air...never really bothered me...until one day...was looking into my front bar...underneath the rego plates...there was a plug that was UNPLUGGED...didn't really know what it was but plugged it back to a socket around the same area...and what do u know....a/c climate control works fine now! It also used to automatically change the blowing mode all by itself...but after plugging tht plug back in...everything has been fine! Try it out and see if tht plug is unplugged...

no idea....cleaned plug and also cleaned temp sensor in dash with compressed air it was dusty as.... still not working properly...... on the top of the dash what is that sensor for.....??? circle looks like a solar panel on passenger side?

thanks for that ran diagnostic test... in the temp display screen ambient sensor showed 19.5'c, in vehicle sensor showed 30'c and intake air temp sensor showed 17'c. so am i right in saying in vehicle sensor is not working as it was definatly not that hot? is this sensor the one to the left bottom of the steering wheel???

Edited by rgr34

when the alarm was being installed i noticed black plastic tube no wires, asked installer what it was, he advised thats for climate control and plugged it back in...he advised he didnt unplug it. is that all it is or is there actual wire connector???? thanks in advance if anyone can confirm this! also got a flashlight and shined it into little grill.... there nothing there besides a small metal wire and round plastic surround... maybe there is no sensor in there already!

Edited by rgr34

hi ppl today had some time removed lower dash and plastic face around dials, plastic tube was plugged in however wire connector was not... this most likely was left disconnected when i had tacho problems and took it back to car yard.... they just left it disconnected......... thanks 666dan & n15mo for helping out that aircon diagnostic tool is cool! alll back to normal now.......

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...