Jump to content
SAU Community

Recommended Posts

Hi everybody,

I am planning to take my R32 to its first run on dyno this coming thusrday, and i am seeking your advices and any tip that helps...like should I raise boost when on dyno or jsut stick to 1 bar?>(tuner's advice)

here are the major mods:

RB25DET Series 2

Garret T04E turbo

3" FMIC

Custom 3" air intake piping

BOV

Turbonetics Evolution wastegate

custom 3" downpipe

Tomie cams (270/8.8 both)

HKS metal head gasket 1.2mm

Walbro 255 in-tank fuel pump

HKS 555cc injectors

SARD standard fuel pressure regulator

Centerforce single plate clutch

HKS N1 muffler with custom 3" exhaust pipes

Greddy Profec-B Spec II

Apexi Power FC

Edited by Light
Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/
Share on other sites

your tuner will tune the car to its potential. so if he thinks it can take more than 1 bar then he'll turn it up.

from the sounds of your setup, it will depend on the maximum allowable flow of your turbo.

also, you havent listed an AFM in your list. is it still standard? if so, you might be restricted with the power you make.

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2739695
Share on other sites

Don't stress mate.

You should expect any were from 230-250rwkw depending on what boost you run

as 250 give or take is maxing out your stock inectors.

As long as it doesn't lean out badly or run too rich you should be safe.

However, this depends on the tuner's experience.

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2739830
Share on other sites

Just pump boost into it until you either get valve float, no gain, or run out of fuel.

I think the limiting factor in your setup is the walbro intank pump. You may find that your injectors are maxing out earlier than expected if it isn't up to the task.

Stock valve springs and lifters will likely stop the fun at about 20psi anyway.

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2740539
Share on other sites

20 will be safe on stock internals.

Just dont expect anything super brilliant in terms of response with a t04e, around 5000rpm before yo'll really see much of a song start :)

It'll make good power, just take a while to do it

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2740980
Share on other sites

around 5000rpm before yo'll really see much of a song start

you are absolutely right R31Nismoid, the song starts :) at around 5000rpm and this is the lag that makes me think of going to a better turbo even before i dyno it. thanks mate

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2741042
Share on other sites

looking at your mods and the condition of your engine

with cams, it should see full boost earlier then it would, with just standard ones.

And i have just a r33 plain bearing hiflow on mine set on 15psi pretty much doin 230rwkw. with pretty much the same mods as you except for cams. My turbo is set on 18psi, but i have been restricted to 15psi because of the standard actuator bleedin off to early.

Having a t04e turbo, ( i haven't had one before, but have seen specs.)

i would be hoping to equal 270rwkw and or higher sittin on 1bar boost.

Just depends how good your tuner is, and what condition all your mods and turbo is in.

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2741063
Share on other sites

on an RB20, there is no way its going to make 270rwkw @ 1bar

I had the old GTS-R turbo on the RB25 which was a t04e front and a hybrid T3 int gated rear... and it came on 13psi @ 4200rpm/220rwkw on the RB25

Check FATGTS-R's results with his version, its taking a bit more than 1 bar to mash out 270rwkw

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2741221
Share on other sites

I recon do yourself a favour and get a better fuelpump, no mention is the walbro direct connection to battery loop or using the standard fuel power source, your setbacks are the pump and turbo choice, let alone its all been said above, ove noticed lowered compression ratio with the head gasket so you should be able to pump in a bit pending on what your turbo allows you to do im guessing? Goodluck on your endevours and keep us posted

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2741259
Share on other sites

well thats fair enough on a rb20, but he has stated its a rb25det series 2

with cams and all the fuel supporting mods.

As i dont have a t04e, i wouldnt know, but looking at my car and he has a bigger turbo, ball bearing??

Maybe not at 1 bar but hopefully it shouldnt be too far off

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2741639
Share on other sites

whops, RB25, didnt read that line :happy:

But yeah, i made 220rwkw @ 13psi with a t04e/hybrid T3 rear... so i doubt its going to be much more different, maybe 20rwkw higher with a different rear. But no more.

If you make 335rwkw, i'll be surprised mate.

The turbo will be working its guts out, and my guess @ somewhere above 24psi will be needed to get there

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2741948
Share on other sites

so mates do you suggest setting the boost on 20psi all the time and that will be safe with no harm to engine at all? Anybody got settings for greddy profec-B spec II for 20psi (gain, set gain, warning...etc) i find it confusing sometimes

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2747202
Share on other sites

Look, its your tuners call.

Some people run into valve float issues when boost gets higher etc.

IMO, ask the tuner to run as much boost as possible.

If the tune is decent and there are no issues. Then really there should be no issue.

If knock doesnt go about 25-30, then it should be fine.

Link to comment
https://www.sau.com.au/forums/topic/146761-dyno-first-run/#findComment-2747564
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...