Jump to content
SAU Community

Recommended Posts

Hey guys,

Just wondering if anyone can give me a few clues as to why my r33 gts-t is hard to start in the morning?

Its got a fuel reg, boost control valve, and a front mount, but it has had brand new coil packs and plugs (splitfire) and everything else seems to be normal, it recently had a tune so its not running rough or idling bad, its just that when i go out in the morning to start my car, i have to pump the accelerator pedal a bit to get it going, it almost seems like a fuel pump or oil pressure problem or something!

I'm just guessing though so if anyone could shed some light i would greatly appreciate it!

Cheers, Jared

:rofl:

Link to comment
https://www.sau.com.au/forums/topic/147177-cold-starts/
Share on other sites

I had the same issue with mine, but mine started to happen after the engine over heated and turned off. To get mine back sort of working alright now. Ive so far done the following.

Cleaned the AAC valve as per the Maintenance tutorial - made idle a lot smoother and drive smoother as well.

Changed the idle to a but higher than normal.

Changed sparkies

Did a pressure test to find out i was losing pressure on all cylinders after the overheat (hate this one)

For now it starts fine and idles good and still has the grunt but not as much as before. Hope this helps

Link to comment
https://www.sau.com.au/forums/topic/147177-cold-starts/#findComment-2750133
Share on other sites

Have you been using it as a daily driver?

Ive noticed that with mine, after using it as a daily driver, it becomes harder to start also, *have to give it a bit of gas* to start it.

Ive found that, if i dont drive it everyday, Problem goes away? strange but true.

Link to comment
https://www.sau.com.au/forums/topic/147177-cold-starts/#findComment-2753067
Share on other sites

this is a very out there thought, but it may be a dribbly injector that is letting a tiny amount of fuel into the cylinder when the car is off.

another out there possibility is that it may be that you have a head gasket on its way out and water is getting into the cylinders.

Link to comment
https://www.sau.com.au/forums/topic/147177-cold-starts/#findComment-2760119
Share on other sites

I got told sparks, and iinjects. got new set of Niridium spark plugs, and got my injects, cleaned, properly, in the that special bath thingo. they checked the flows on the injects too, all perfect.

Problem still there.

its a pain in the a$$, when mechanics guess, and you pay.

where is this ACC valve? i been hearing about?

Link to comment
https://www.sau.com.au/forums/topic/147177-cold-starts/#findComment-2760286
Share on other sites

the aac is at the back of the intake plenum. its at the top. that doesn't control the cold start function though.

the iac is under the plenum below the aac. much harder to get to.

also i would recommend not using iridium plugs. they don't seem to last any longer or perform any better. they just cost more. i pulled a set of iridiums out of 180sx the other day that were dead after about 7000ks. the coppers i've had in my car are still running fine after 5000ks. i'm going to replace them at the next oil change in a few weeks time, but you can buy a full set of coppers for about the price of 1 iridium plug, and they last nearly as long.

Link to comment
https://www.sau.com.au/forums/topic/147177-cold-starts/#findComment-2760500
Share on other sites

Unless you have a tunable ECU you can't 'tune' the car...Only check/change things like ignition timing, s/plugs, coils, clean air flow meter, air filter, check compression etc...

All in all i'd be biting the bullet and taking it to a reliable mechanic to properly inspect the car and diagnose the problem. Its next to impossible to work out what a problem is without a trained pair of eyes seeing the car. Just because someone else had a hard to start problem doesnt mean its got anything in common with yours and its a waste of time guessing.

Edited by Godzilla32
Link to comment
https://www.sau.com.au/forums/topic/147177-cold-starts/#findComment-2761684
Share on other sites

Just because someone else had a hard to start problem doesnt mean its got anything in common with yours and its a waste of time guessing.

i agree with you about the fact that this problem may be completely different to someone elses, but i don't think it is a waste of time guessing. if you can sort the problem out without spending money then you are ahead. if all else fails then take it to a professional.

Link to comment
https://www.sau.com.au/forums/topic/147177-cold-starts/#findComment-2761718
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...