Jump to content
SAU Community

Rear Diff. LSD???

lambo
 Share

Recommended Posts

SteveL Mentor

SteveL

Posted
Posted

Pretty much impossible to tell from a photo, but the finned cover suggests it might be a viscous LSD. Try jacking up the rear end (both wheels off the ground), then turning one wheel - if the other wheel turns in the same direction, then you have an LSD, but if it turns in the opposite direction it is an open diff (probably - i've seen completely stuffed LSD's act in the same way as an open diff).

RC45 says you have an R200 diff with 4.5 gears.

Link to comment
https://www.sau.com.au/forums/topic/14735-rear-diff-lsd/#findComment-298509
Share on other sites
lambo Enthusiast

lambo

Posted
  • Author
Posted
Originally posted by SteveL

Pretty much impossible to tell from a photo, but the finned cover suggests it might be a viscous LSD.  Try jacking up the rear end (both wheels off the ground), then turning one wheel - if the other wheel turns in the same direction, then you have an LSD, but if it turns in the opposite direction it is an open diff (probably - i've seen completely stuffed LSD's act in the same way as an open diff).

RC45 says you have an R200 diff with 4.5 gears.

I jack the car up last week and when i turn 1 wheel front or back. The other doesn't move at all. Is it spoiled?

Where can i find info on how to tell what type of LSD i have and if it is damaged or worn?

Link to comment
https://www.sau.com.au/forums/topic/14735-rear-diff-lsd/#findComment-298548
Share on other sites
Guest 382 GZV - 4 Door R33

Guest 382 GZV - 4 Door R33

Posted
Posted

Turning a wheel while your car is on a car may not cause the other to turn as well for both an open wheeler and LSD - the other wheel will only turn definately if you have a Locked diff.

The 4.5:1 is better for fast pick up and drifting although you'll go thru fuel way quicker.

One way of telling (the way I found out at least) is to go to a quiet road and do a long 2nd gear burnout (dumping the clutch hard so as not to allow it to slip) - do the burnout for about 5 metres and get out and check - if there's 2 black lines, it's working if there's only one, then it's broken or it's an open wheeler.

Link to comment
https://www.sau.com.au/forums/topic/14735-rear-diff-lsd/#findComment-298896
Share on other sites
SteveL Mentor

SteveL

Posted
Posted
Originally posted by 382 GZV - 4 Door R33 Turning a wheel while your car is on a car may not cause the other to turn as well for both an open wheeler and LSD - the other wheel will only turn definately if you have a Locked diff.

If the LSD is working (at all) both wheels should turn together....on an open diff they will turn in the opposite direction because that is the nature of the mechanism. The ONLY way this won't happen (either case) is when something else is preventing it (eg brake pad drag).

Link to comment
https://www.sau.com.au/forums/topic/14735-rear-diff-lsd/#findComment-298919
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      I forgot about my shiny new plates!
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...