Jump to content
SAU Community

Sa Rego'ing An Interstate Rego'ed Car?

beno33

By beno33,
in South Australia

 Share

Recommended Posts

beno33 Apprentice

beno33

Posted
Posted

Hey guys,

Im looking at buying a car from interstate, either VIC, NSW or QLD at this stage, but I have a question some of you might be able to help me with.

If I buy a car that has interstate registration, and go to re-register it in South Australia, does it need to go through Regency, or does it just need to undergo a quick chassis/engine number check.

I have check at my local transport customer service centre, and they lady just gave me a form, told me to fill it out with the purchased vehicle's information, then take the vehicle to my local police station, where they will verify that the vin number etc is all ok and pay $44 and they will swap the rego over to SA. She said it was not a roadworthiness inspection. This would be good as the car will probably be a little bit modified and I dont want the hassle of going through Regency with my new pride and joy.

But I have also heard that EVERY single car being rego'ed in SA needs to undergo a regency inspection. I cant see how this would be the case as there must be loads of cars coming in, but if a regency inspection is required, then I'll probably can the idea of going interstate and driving it back.

If someone has been through the process and/or could shed some light on the matter, it would be greatly appreciated.

Thanks very much,

Ben

Link to comment
https://www.sau.com.au/forums/topic/148164-sa-regoing-an-interstate-regoed-car/
Share on other sites
sinistaGTR Grand Master

sinistaGTR

Posted
Posted

If you get the car registered in your name in another state. you do not haver to get any checks done....as long as the car is in the name that wishes to be transfered and has current rego, you just need to go to any transport SA office. so if your worried bout mods etc that might be easier to do than changing the mods back.

Mr Sniper911 Community Regular

Mr Sniper911

Posted
Posted

I got mine from Vic..... all i had to do was go to the loacal police station get the vin and engine number checked and take the form to the rego office and there ya have it.....

This is straight from the transport sa website:

Interstate vehicle registration

You must register your vehicle in South Australia within three months if you move from another State or Territory of Australia and become a permanent resident.

Unless you hold a current interstate registration certificate in exactly the same name as the intended South Australian registration, the vehicle must undergo an identity inspection to confirm the correct identity of the vehicle. The vehicle can be inspected at the following inspection stations upon payment of the correct fee .

If you live within a 40 kilometre radius of the Adelaide GPO , the vehicle must be inspected by the:

Vehicle Identity Assessment Station and Safety Group

7 Naweena Road , Regency Park 5010

Open: 8 am – 4:30 pm, Monday to Friday (except public holidays).

No appointment is necessary.

If you live more than 40 kilometres from the Adelaide GPO , you may have the vehicle inspected at

your local police station.

Please contact the police station to arrange an appointment.

or

Vehicle Identity Assessment Station and Safety Group

7 Naweena Road

Regency Park 5010

Open: 8 am – 4:30 pm, Monday to Friday (except public holidays).

No appointment is necessary.

See vehicle inspections for more information.

Once the vehicle has been inspected, you need to present the inspection certificate or post to a Customer Service Centre along with:

your completed ‘ Application for Registration and Third Party Insurance' form

your inspection certificate

proof of identity if you have not previously been issued a licence or registered a vehicle in South Australia

the appropriate fees . Calculate applicable fees by visiting http://ecom.transport.sa.gov.au/.

The following fees may apply:

registration fee

third party insurance fee

stamp duty on insurance

stamp duty on value*

number plate fee

postage fee (if you request the number plates to be posted to you)

administration fee, level 3

Emergency Services Levy

inspection fee.

After you have registered the vehicle in South Australia , you can apply to the State where the vehicle was previously registered for a refund of registration fees.

Stamp duty*

If the vehicle was registered in your name in another State, you will need to produce the current certificate of registration from that State when you apply for registration to be exempted from paying stamp duty on the value of the vehicle.

Mr Sniper911

Giveitall Community Regular

Giveitall

Posted
Posted
I purchased one of our skylines in Qld and took it to Sturt Street Police Station for the Vin check.

got mine in gold coast and went through sturt with no problems.

i recalled that the vin check station only open two days per week.

beno33 Apprentice

beno33

Posted
  • Author
Posted

Thanks for all the replies fellas, I'm about 60kms from the Adelaide GPO so should be right to take it to the Nuri cop shop if I decide to get one. Looking at a toyota chaser for a daily driver. Hopefully it all works out...

Thanks for your help guys, much appreciated.

Ben

PRO AERO Collaborator

PRO AERO

Posted
Posted

im doing the same procedure.its not actualy regency its another place around a few corners from there a bunch of older fellas look over it.im going to try go thru sturt to thoe ll just sey i live at victa.also will my plenum be anything to be fussed over???

487304.jpg

4door_Sleeper Veteran

4door_Sleeper

Posted
Posted (edited)

Just a couple of obvious things to consider.

Is the Pod secured?

What happened to the std boost controler? (hoses dont look right)

Remove the Malpassi Srising rate Reg and replace it with a std one.

Whart have you got mounted om the right hand strut tower (in front of the master brake cylinder)? Alarm?

Where/what has happened to the BOV, is it still a return system?

These are just some of the things I can see (a larger pic would help) that might be of interest to the MVI unit.

Im not trying to give you a hard time, just point out the things that caught my eye (and I assume they see a lot of skylines)

Edited by 4door_Sleeper

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...