Jump to content
SAU Community

Recommended Posts

Hey guys...

Im currentlly mid modification in doing my GT30 high mount so i have all the bits for sale that i dont need...

I also dropped a spanner down my front guard and took two massive chips out of the paint :cry: so I need more money to fix that...

I have the following for sale and a few pics at the bottom of some of the stuff...

1. R33 GTS-T Series 2 Turbo

It is in execptional condition and has only travelled just on 80,000kms.

The wheels are very clean with no chips and like i said in tip top condition.

It has the nylon Series 2 compressor the fastest spooling of all stok turbos.

SOLD

2. Exhaust Manifold

Not much to say about this as there is nothing to them.

It is in good condition with no cracks.

Price $70 $50 $30

3. Standard Intake pipe from AFM to Turbo (comes with the bov dump pipe and crank case vent pipe also)

Good condition, not needed with upgrade.

SOLD

4. Standard Brake Rotors

Good condition

Replaced them with slotted rotors for race use.

Price $100 $80 $60

5. Standard Brake pads (90% meat)

Full set front and rear for Series 2 R33

SOLD

6. Standard Clutch & pressure plate (60-70% meat)

The clutch is a standard Nissan part, was put in car in Nov 04, went 5000-6000kms before being replaced with a twin plate.

$150 $75

7. Split Exhaust Dump pipe

Twin dump pipe for standard R32/33/34 turbo

Worked great and helped with pick up off gear changes

It also has an extra tap in for an exhaust temp sender, but if you dont need it just block it off with a capped nut.

SOLD

8. R33 GTS-T Series 2 Injectors

6 x Standard Injectors - 2 of which have broken caps - All in good working order

Price $300 $150 $75

9. Banjo fittings & rear gasket

As picture shows below, all in tip top condition

SOLD

10. 1 x HKS Adjustable Timing Gear (suits all rb's)

The new one with the purple centre and the silver outer...

Dont need it as i have HKS cams now...

Used it for 3000km's

SOLD

11. R33 GTS-T Series 2 Stock ECU

I have a pfc so i dont need it...

Price $200 $150 $100

12. Series 2 AFM (3 Wire)

Comes with plug and short amount of wire.

Replaced it with a Z32

Perfect Condition

Price $100 $80

13. Stock R32 AFM

Price $100 $80 $60

14. Just Jap R33 Engine dampner

Blue in colour, does nto fit now with new plenium in place

Will fit all R33 GTS and GTS-T's from 93-98

Comes complete and in very good condition

SOLD

15. Stock R33 BOV

SOLD

16. Coil Packs x 6 (Series 2 R33 only)

Standard units, upgraded for split fire units

SOLD

All interstate buyers are responcable for any postage costs...

Local delievery/pickup in the Brisbane Area...

Here are some photos...

post-2979-1166683671.jpg

post-2979-1166683686.jpg

post-2979-1166683699.jpg

post-2979-1166683716.jpg

post-2979-1166683738.jpg

post-2979-1166683757.jpg

post-2979-1166683793.jpg

post-2979-1166683809.jpg

post-2979-1167621914.jpg

post-2979-1167621941.jpg

post-2979-1167622115.jpg

post-2979-1167622138.jpg

Edited by Col-GTSX
Link to comment
https://www.sau.com.au/forums/topic/148263-r33-gts-t-bits-and-pieces/
Share on other sites

7 PM's for the dump pipe and all returned and all calls returned...

4 PM's for the turbo have been replyed also...

3 PM's for the clutch

& 1 for the brake pads...

OMG... All that and still not sold, first in best dressed people...

Prices are fair and obviouslly very cheap to get this much attention in such a short time...

Please dont insult me with $100 offers for the turbo...

$500 is firm on the turbo as it is in exceptional condition...

Hey guys, sorry bout the late reply, xmas and all...

how much more power would just that upgrade give?

It will basiclly flow more air you should expect a good extra 15rwkw at 10psi over standard R32 trubo at 10psi...

hey man is that cam gear for ex or in side, tenx put up some pics eyy!

The cam gears are the same, so you can use it on either the exhaust or inlet...

It looks like this....

13197_hks%20cam%20gear.jpg

pm sent

Reply'ed

will the r32 dump pipe bolt on to the r33 turbo?

yes, they are the same...

Nope... You may have to replace the silicon pipe that goes from the turbo to the intercooler tho as i found my 32 one was pretty stiff and not very flexiable anymore...

But other than that its bolt in and out...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
×
×
  • Create New...