Jump to content
SAU Community

Recommended Posts

There are a few differences, one being the sensor plugs on r32 are round, square on a31. Also the r32 engine has a little more power in stock form. The r32 has factory bov and a31 doesn't. I have heard there is more potential for higher power outputs from the a31 engine, not exactly sure how or why though. Not sure on if the turbos are the same

Edited by Love_Hate

The cefiro inlet cam has a longer duration and the exhaust cam is retarded about 2 deg from the R32 cam.

ceff afm, coilpacks and ignitor are different.

ECU also only has 1 fuel map and 1 timing map as opposed to the skyline. it has 2 fuel and 2 timing maps.

If you look at the 2 maps the skyline runs 3 deg more timing and has different load tp scaling.

thanks for all the replys so with these spitfire plugs can u get spitfire coils that u can just plug in to replace the stock coil packs over coil pack problems?

They are adapters. http://www.skylinesaustralia.com/forums/in...mp;hl=splitfire Seems Splitfire didn't want to manufacture different coilpacks for the same engine. If you could get hold of a R32 coil pack loom and are 1/2 handy with electrics you could easily knock some up yourself.

They are adapters. http://www.skylinesaustralia.com/forums/in...mp;hl=splitfire Seems Splitfire didn't want to manufacture different coilpacks for the same engine. If you could get hold of a R32 coil pack loom and are 1/2 handy with electrics you could easily knock some up yourself.

so that is only for the adaptors then u would have to get ur hands on some 32 coilpacks to plug in them or do u buy the aftermarket ones as shown on the pics below the adapters ?

  • 2 weeks later...

the turbo is different also, R32 is ball bearing ceffy is plain bearing. also slight differences in the exhaust side.

later ceffys run the rounder R32 style loom plugs, but most are early ones

AFM, coils, CAS and some other sensors are the same as R31 Redtop RB20DET. turbo is also the same as that of a redtop.

loom (bar the plugs), injectors, head is all the same as r32.

while working on my dad's cef (series 1) I found that it had more parts in common mechanically (well, engine and electrics) with the R31 GTSR than it did with the R32 GTSt.

  • 4 months later...

i just found out that my R32 RB20DET engine is being run off a cefiro ECU...

can anyone tell me if this is dangerous for the engine?

i'm trying to track down an R32 ECU, but having no luck so far...

if anyone can help me by answering that question, it would be GREATLY appreciated... :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...