Jump to content
SAU Community

Recommended Posts

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i was lucky, most of the mods came with my car FMIC, 3" exhaust, 10psi, pod, tanabe coil-over suspension, and a few more minor mods.

Hows the hunt for the R32 going?

ah, nice one. easier when it comes with the mods how long have you had it for?

checking one out this weekend.. ill try and getr the engine checked out, and if its all good ill make an offer for it.. its pretty stock, exhaust and a couple of things

ah, nice one. easier when it comes with the mods how long have you had it for?

 

 

checking one out this weekend.. ill try and getr the engine checked out, and if its all good ill make an offer for it.. its pretty stock, exhaust and a couple of things

i think ive had my car for about a year now, i originally was looking for an R32 when i bought my 33, there wasnt really enough R32s to choose from over here, so it was a bit easier to find a nice 33.

Sounds good, if the engines good and the bodys straight and everything is in order! how many have you looked at so far?

dang! ah wells he'll pop his head in here later tonight - when were all asleep!!!

maybe he should be our postwhore where u and me are asleep sam.

:) he can reel off posts like he does on msn, just put 10 down, dissapear for 15 minutes, then put another 10 down

I've looked at heaps online and in the paper and stuff.. but only a couple have been what im looking for .. checked out a couple that you can tell they have engine trouble as soon as they turn it on... so im hoping this one checks out..only problem is, it isnt registered in NSW, so I will have to get a blue slip for it

dang! ah wells he'll pop his head in here later tonight - when were all asleep!!!

maybe he should be our postwhore where u and me are asleep sam.

Dun worry fella's I'm always up late playing VC.. so I can be ur part time nocturnal post whore.. a bit lonely..but hey .. that's country life.. lol :)

I've looked at heaps online and in the paper and stuff.. but only a couple have been what im looking for .. checked out a couple that you can tell they have engine trouble as soon as they turn it on... so im hoping this one checks out..only problem is, it isnt registered in NSW, so I will have to get a blue slip for it

thats a pain, you guys have to have all these roadworthy inspections over there, right?

Dun worry fella's I'm always up late playing VC.. so I can be ur part time nocturnal post whore.. a bit lonely..but hey .. that's country life.. lol :)

country life? where abouts are you? i thought you lived in adelaide

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...