Jump to content
SAU Community

SA Wasteland?

MM2death

By MM2death,
in South Australia

 Share

Recommended Posts

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

or we could have it at my place - I have a projector and big screen :) .... just gotta figure out a way to get rid of the wife for the night :)

Love your sig avi Duc ... go the R34 4 door :)

I'm off to play some BattleField 2 Demo now, so won't be lurking anymore ..... catchas later

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Deluxe Grand Master

Deluxe

Posted
Posted
Can I have your opinion on this guys. Thinking of getting it as my daily. Dont laugh, serious question.

7766.jpg

Hey duc!! If you want one of those as a parts runner, be cheap as on the old fuel, and a little bonus is, they come out with the E15 motor as seen in the little ET Pulsar(turbo), would be a sweet straight bolt in engine change. and not to mention some fun!!!

Nozila Grand Master

Nozila

Posted
Posted
Hey duc!! If you want one of those as a parts runner, be cheap as on the old fuel, and a little bonus is, they come out with the E15 motor as seen in the little ET Pulsar(turbo), would be a sweet straight bolt in engine change. and not to mention some fun!!!

If they had one avaliable in adelaide, then sure i would think about it. Would be wicked to transport parts ie bonnet/bodykit/wheels around in that thing. Imagine the looks you would get driving down a street like rundle st in that thing. Hehehe

Sambo33 Grand Master

Sambo33

Posted
Posted

nice pics there duc.

sanding work looks good, but its hard to tell from a pic. looks like youve been using water too, just a tip - clean all the sanding sludge that has run down the front of the car up with a sponge after you finish sanding, if its left for any amount of time or the sun gets on it it can be hard to clean off later. :)

Nozila Grand Master

Nozila

Posted
Posted

hehe

oh btw sam, say if i was to paint it in acrylic would the acrylic primer be ok on top of the current primer that is on the hood or do i need to sand back to the red coat underneath that. I know that acrylic/2pak dont mix, so im kinda dumb founded.

Sambo33 Grand Master

Sambo33

Posted
Posted

just prime straight over the top, no matter what paint it is, it would be dificult to sand the colored layers off by hand. you just need to keep in mind that the acrylic paint has more of a chance of 'biting up', than 2k

Sambo33 Grand Master

Sambo33

Posted
Posted

like how the guards looked before you sanded them, you could see all the sanding marks in the paint. also on the bootlid where they removed to spoiler & patched up the holes, you can see the 'bite up' lines where they put the poly-filler

Sambo33 Grand Master

Sambo33

Posted
Posted
taking bout hands, i have like blood blisters and crap cause of the sandpaper :pissed: My thumb and index finger are so sensitive now.

really? ive never had that before. if you have sensitive skin, be careful when using thinners & solvents, that stuff has recked my hands.

Nozila Grand Master

Nozila

Posted
Posted
really? ive never had that before. if you have sensitive skin, be careful when using thinners & solvents, that stuff has recked my hands.

yeah i cant stand wearing gloves - pansy!! hehe. so i just use my bare hands and a block i made to sand it. I think the hrs upon hrs of my hands (right one) being soaked has not helped it.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...