Jump to content
SAU Community

Recommended Posts

Son of Sydneykid: Do u mean a seperate dump pipe that comes off the wastegate? Because i'm pretty sure its one pipe Covering the turbo housing and the wastegate ( i'm not sure whether thats the right way of putting it ;) ) Basically...its a 3 inch dumpipe from the turbs....3 inch cat and from the cat back a 3.5 inch.

Guest 382 GZV - 4 Door R33

How much rwkw are you expecting to get gester??

I would have thought that a 3" was fine for standard size turbo and over 300rwkw.

I even heard of a VL turbo (has an RB engine so it's acceptable) doing 8 sec 1/4 miles was using a 3" system.

The note's probably louder if that's what you want - or else you can do what I do and have a 3" exhaust with no muffler. That is loud enough ........ well it's been getting softer lately, I think it may be me going deaf to that frequency though :zap: :(:)

Yeah just that I have a choice between 3.5 and 3" so if its pretty uneccesary then I'll just stick to 3" as lower range power is better for me. Im aiming for around 180-200kw.

With the muffler I know usually they dont make much of a difference but surely a twin tip muffle would be different then say a 4" tip? What would be the best sort of muffler to get with a 3"?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...