Jump to content
SAU Community

Recommended Posts

I thought i would give this a go for a bit of fun when i go to my gf's house with a whole pack of v8's that live over the road.

Im a little unsure on what to do...

Steps 1, 2 and 3 i can do (is it saying i should hear lumpy idle now?)

Where it says to turn the car off and dial back the crank angle sensor, is that listed under 'cranking'?

I think the rest is pretty straight forward after that.

Cheers

1. Turn car ON

2. SETTING, IGN/INJ

3. Press DOWN 1 time

If you observe lumpy idle then note the number ie: -1 If you don't observe lumpy idle, press DOWN again. Keep repeating until you get lumpy idle, don't go past -3 or -4 it's too much. Now with that number in mind do the following

1. Turn car OFF

2. Dial back the Crank Angle Sensor whatever number you had in IGN/INJ Adjust, so if you had -2 dial it back 2 deg

3. Turn car to ACC

4. Edit the IGN map and shift every cell UP whatever number you used in #2. So if it was -2 then add 2deg timing to every IGN cell on the map

3. Turn car ON

4. Observe lumpy idle

Link to comment
https://www.sau.com.au/forums/topic/149181-powerfc-cammed-lumpy-idle/
Share on other sites

I remember when i first installed the GTR injectors and had the PFC base map it was lumpy as hell. It was that rich i think it would of fouled the plugs if i let it idle that long :)

So yeah adding more fuel at the cell at idle would make it do that also.

my tune does it every now and then, the main cause is its cell bouncing between different IGN spots, you can see it on map tracer, quickly swapping between two cells, if the ign varies alot on the adjacent cells it will lump around heaps. you can also getting it from messing with the afm ducting pipe width.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...