Jump to content
SAU Community

no BOV = anyproblems??


Recommended Posts

well as its a stock one.....it looks nothing like an aftermarket one. not sure about 32's but on a 33 they're this ugly small grey roundish thing thats attatched to one of the intake pipes. follow ur intake pipes and there should be something odd bolted onto it:D as u say your hearing a whistling sound after lettin go of the gas its best bet that thats the sound of ur bov...doesnt matter if its auto too.....my friend had a 32 auto.

Guest RaBZ3174

oh ok thanks alot man..yea i think thats y i didnt think there was a BOV cauz it didnt look like an aftermarket one and didnt generate as much noise as my freinds r33..although i still ran him off the rd.. im gonna go look for the grey roundish ugly thing :P thanks alot mr fanny!!!

if theres no affect on the motor through a BOV why then do most factory turbo cars have BOV's stock?

AFAIK thier there to improve response by decreasing the chance of backpressure slowing the compressor when the throttle is slammed shut.

or boost spikes?

I put my aftermarket BOV on so i could have something quieter than the stock one. My old stock one used to make a HEAP of noise (probly because of my air filter pod) and was really sensitive.

Whenever i came on boost with the stock bov i couldnt hear the motor underneath the sound of air rushing. Aftermarket BOV has reduced the noise by over 50 percent id say, now all i hear is the howl of 6 lovely RB cylinders. Not sure if all 32 bovs were as bad as my one or if mine had a problem. But its better by far now.

Red17

kwazza: i think u've missunderstood. i dont think anyone here said that having no bov wont do anything to ur engine. just reinforcing to Rabz that his car and all gts-t's have stock blow off valves...be it auto or manual. Predator and i were just saying from opinion that an aftermarket one's over the stock one wont give u any great performance gains.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey   ive gone for a terminated harness on my build so selling brand new unused and unopened piggy back harness  https://www.haltech.com/product/ht-141357-elite-2000-2500-nissan-skyline-r32-33-r34-gt-r/ Located Bathurst NSW   price $600 + postage     
    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
×
×
  • Create New...