Jump to content
SAU Community

Recommended Posts

wait till i test it, if you come for a drive down from qld i will enable it for you for free :)

everyone else has to pay $50 :thumbsup:

that is wicked!

If you get it working I would be happy to work out some deal with you so that i can have it enabled on mine! :P

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

  • 10 months later...

After reading all of that Im still confused, Using a normal Bee-r limiter, like the ones sold on SAU right now, is it likely to damage your turbo if u hit the limiter often? or say a couple of times each time you go for a drive,

So whats the cheapest option for a 0km/h (stationary) rev limiter? Have always thought about one of these, i don't really care about the ignition cut as i don't want to destroy the cat so i don't wanna spend $300 on a BeeR.

I'm guessing you can't do something with the LT12S to do it?

Yeah see i'd rather not do that (even though it would be fun shooting huge flames and launching on boost).

Would rather just a normal rev limiter (fuel cut) on stand still so i can dial in the exact rpm to launch from. Similar to what the new FG falcon's have, hold in the clutch and flloor it and it limits revs to like 4000rpm or whatever.

So whats the cheapest option for a 0km/h (stationary) rev limiter? Have always thought about one of these, i don't really care about the ignition cut as i don't want to destroy the cat so i don't wanna spend $300 on a BeeR.

I'm guessing you can't do something with the LT12S to do it?

The microtech probably has the option in there. Have a squiz at the manual for it /software.

Hmm ok i had a look in the manual and there is an Aux Input function that sets a rev limiter when the (12V) Aux input is activated.

Explains it furthur saying "You can hook up a 12V switch to the AUX input and set a limit figure in the InpRPMlim screen and use the InpTiming screen to retard timing slightly. When the button is presed, the engine will be limited to this rpm figure, and the timing retarded. Releasing the button will deactivate the rev limiter and return the timing to its normal value, allowing the engine to instantly produce full power. This way you can very easily use the Aux Input to set up a basic two-step."

So in other words, you could somehow hook it up to the handbrake and have the rev limiter set until you release the handbrake?

Might look into this furthur and play around with it a bit.

Edited by PM-R33
  • 5 months later...
  • 3 months later...

digging up an old thread but i was researching gizmo products and came across this thread.

Note that's the new Launch interface allows timing retard settings and support for other engines

http://tunertools.com/proddetail.asp?prod=GZM-G0919

being used on a Silvia, sounds like rb25

small demo on the shift light that integrates with the launch control

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
    • Update 1: I did some work on the car already before finalizing this post and my "issues" list. I dropped the Tomei exhaust in favor of the HKS Hi Power Silent. Sounds nice and I can actually hear myself think now. Also gives me a realistic chance to legally drive without silencer inserts. A bit of cheating was necessary to still be able to mount the Top Secret style diffuser. Some malusage of washers and a bit of "convincing" toward the brackets and exhaust hanger seemed to do the trick. The shaky steering wheel has been resolved as various suspension components were worn, like sway bar bushings and link bars. Most notably the two steering tie rod ends. Had some trouble finding bushings because my sway bars are not OEM thickness, 23.x up front and 27 rear. But non adjustable, so no aftermarket I suppose. Maybe they are nismo units? Turbo oil drain hoses were definitely still the originals and are new now. Wasn't the cause of the turbo oil leak sadly. Currently removing the rear turbo because of it, I suspect the braided oil feed line is the culprit. This issue needs to be dealt with so I can work towards actually getting the turbo setup legal and inspected. Two new issues to add to the list as well. Rear Main seal is probably leaking. Time will show how bad it is, I don't really want to drop the gearbox right now just for the stupid seal. Could fix a few other things in one go once I do that. Front right driveshaft grease is going past the cv boot, so at some point I'll fix that too.
    • Ok so no 4cyl clutch... Yeah it is a factory manual. So if iam correct i need clutch and flywheel too? I can use something that suits something like R32 GTST?   EDIT: https://www.ebay.com/itm/224291042776 Is this ok?   EDIT2: i maybe forget to mention this(dk how important it is) but the trans will be behind RB25DET NEO(iam doing swap) It will be there for a little while. Iam planing to do bigbox or BMW tranny..
    • You're probably right about that one. Thanks for your suggestions, I hope I don't need a new 3rd brake light. Although wiring issues might arguably be worse. Right now I'm in the midst of a turbo removal because of my oil leak, other problems are going to have to wait for now.
×
×
  • Create New...