Jump to content
SAU Community

Recommended Posts

We wondered where Nissan Motor Co. Ltd. possibly could go with its VQ-series 3.5L DOHC V-6 after winning a 10 Best Engines award for a dozen consecutive years. After all, most contemporary engine families don't last this long, much less last this long at the top.

So where is Nissan going? To the podium for its 13th award.

The company's engineers apparently don't intend to relinquish the VQ's now-legendary status as the definitive V-6 benchmark because this year, the fourth generation of the VQ is 80% new, flaunting revised design features that address the one development aspect in which the VQ had been slipping refinement and brewed in a fresh new level of performance, just to be certain everybody knows they're serious.

In recent 10 Best Engines competitions, Ward's editors have been straightforward about the VQ's benchmark role: It's tough to rag on a legend, but ever since the 02 model year, when Nissan bored the sweet original 3L VQ to a brawnier 3.5L, we've noted an erosion of refinement. Noise, vibration and harshness levels had been sacrificed at the altar of increased horsepower and torque.

The modular DOHC V-6 that launched in 1995 in the U.S. at 3L and 190 hp gradually had grown to 3.5L and as much as 298 hp - a 50%-plus hike in power from just a 17% increase in size.

But for the fourth-gen 07 variant, the VQ35HR, there's a critical new structural ladder frame, an enlarged crankpin and crank journal diameter, a new cylinder-head design, a trick new asymmetric piston skirt and longer connecting rods, in addition to a raft of friction-reducing updates.

The engineers out there easily will assemble the puzzle to see improved NVH was a prime target. It worked. The VQ has regained much of its hallowed silkiness. Once again, it's easy to forget to upshift, it revs so smoothly, Editor Drew Winter says.

But all that refinement attention bore gifts even better than those best appreciated by the J.D. Power quality fanatics. The HR designation for this latest-generation VQ stands for high revolution, meaning there are more revs available from an engine that always preferred the high-altitude section of the tach to begin with.

The VQ35HR now offers a luscious 7,500-rpm redline (up from 7,000 rpm with the manual transmission for the old VQ) and revs so passionately that a gearshift feels unnecessary before 6,000 rpm.

A 6,800-rpm power peak would be a warning sign in less religiously detailed engines. But for the new VQ, that region of the tach is fully and invitingly exploitable.

All those revs mean extra power, too, and the HR variant of the VQ (a fourth-gen VQ35DE with fewer of the high-rev ministrations will be fitted for several models) loads up with 306 hp and 268 lb.-ft. (363 Nm) of torque / power that matches the class-leading Lexus IS 350's 3.5L DOHC V-6, but lags it slightly in torque.

Nissan engineers say they developed the high-rev variant of the 3.5L DOHC V-6 to be a more emotional experience, and we're down with that, too.

Anytime you can spin a V-6 to 7,500 rpm, get more power and refinement and bask in magnificent new sounds specifically targeted for the HR, there's nothing to do but once again award the champion its hard-earned belt.

Source: Wards Auto

post-20773-1167866229.gif

Edited by scathing

Still, its only making an extra 8hp with that extra 500rpm of redline, and new internals. Although the shot on the Wards site doesn't show it, I believe its meant to have a dual intake rather than the single the older VQ's have had.

I would have expected far more power than just 8hp at the flywheel, especially if it spins more smoothly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...