Jump to content
SAU Community

Recommended Posts

When should i upgrade my fuel pump?

My mods are:

Apexi pod

CAI

FMIC

Turbo back exhaust

Boost controller set at 9psi

Power FC coming in a few weeks.

I think at the moment ill be making 165rwkw.

Will fitting lets say a walbro 255L jobbie increase the pressure to my injectors?

I have to change the voltage too dont i?

CHEERS

Link to comment
https://www.sau.com.au/forums/topic/149938-when-should-i-upgrade-my-fuel-pump/
Share on other sites

mate walbro is bolt in replacement and very cheap to ad!... my fuel pump failed and cost me a motor. for the price of say 200 odd its well worth it and eventualy your gona need it. if you boost it i would ad a larger volume pump

talking from personal experience, at the same stage as u i had to change my fuel pump as it was on the brink of dying at that power level. Ive got a walbro, and it seems to be doing the job. either that or u can go for bosch 044 or 040. But defineitly if ur going to tune ur pfc soon, do the pump before this. No need for reg or injectors yet...and what ryan said :D

Edited by moonus
talking from personal experience, at the same stage as u i had to change my fuel pump as it was on the brink of dying at that power level. Ive got a walbro, and it seems to be doing the job. either that or u can go for bosch 044 or 040. But defineitly if ur going to tune ur pfc soon, do the pump before this. No need for reg or injectors yet...and what ryan said :D

The walbro ones are good for 300rwkw arnt they?

See the FAQ/DIY section, there is a thread there showing you how. Up till 200rwkw I'd say with a new walbro you'd be OK without it. but after this you should think about doing the mod.

See the FAQ/DIY section, there is a thread there showing you how. Up till 200rwkw I'd say with a new walbro you'd be OK without it. but after this you should think about doing the mod.

Thanks mate

Do i need to change the voltage on the pump to a higher voltage?

If your gonna upgrade then dont worry about the voltage relay. It's just a neat trick for people who cant afford to upgrade their standard pump

You should upgrade the voltage line, stock or aftermarket pump IMO.

The one problem most people have when installing a bigger pump, is it does not flow the fuel thats required/specified.

The reason being is that people use the factory wiring loom for the fuel pump, and it just doesnt let the pump see the power it needs.

For you "stockish" application... its no worry generally speaking.

However, later on down the track (6-12-18months) if you change turbo and suddenly run out of fuel... you wont remember that you didnt upgrade the volts back when you did the pump, which could turn into a pain trying to work it out :laugh:

Hence i would say just get it over and done with now and save time later... but thats just what i would do

Also that Walbro will not support 300rwkw. I would not go over 240rwkw.

I had about 250 odd and pulled the return line off to see how much was flowing back to the tank when revving hard on the dyno. The flow completely stopped!

You should upgrade the voltage line, stock or aftermarket pump IMO.

The one problem most people have when installing a bigger pump, is it does not flow the fuel thats required/specified.

The reason being is that people use the factory wiring loom for the fuel pump, and it just doesnt let the pump see the power it needs.

For you "stockish" application... its no worry generally speaking.

However, later on down the track (6-12-18months) if you change turbo and suddenly run out of fuel... you wont remember that you didnt upgrade the volts back when you did the pump, which could turn into a pain trying to work it out :)

Hence i would say just get it over and done with now and save time later... but thats just what i would do

I hear what your saying........I guess I assumed that only an idiot would buy a 250KW pump for a 250KW application. Sorry for assuming

You should upgrade the voltage line, stock or aftermarket pump IMO.

The one problem most people have when installing a bigger pump, is it does not flow the fuel thats required/specified.

The reason being is that people use the factory wiring loom for the fuel pump, and it just doesnt let the pump see the power it needs.

For you "stockish" application... its no worry generally speaking.

However, later on down the track (6-12-18months) if you change turbo and suddenly run out of fuel... you wont remember that you didnt upgrade the volts back when you did the pump, which could turn into a pain trying to work it out :)

Hence i would say just get it over and done with now and save time later... but thats just what i would do

I'm letting my mechanic install my pump very soon, it's a bosch 040, do I just tell him to upgrade the voltage line also, or do i need to buy some specific wires/parts etc?

Read the FAQ, its not a case of upgrading the line [yes the mod is an upgrade, but the stock line remains the same]. What you are doing is supplying a direct voltage feed to the pump via a relay. You are using the stock wire as an on/off signal carrier.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was using the wiring diagram I have So 12.74V is coming into the rear Fuel Pump relay as I measured.  When I turn the key to ON im getting 0.6V to the Fuel Pump plug; which i assume is backfeed voltage and doesnt include the 12V from ignition power.  The rear relay is working and being triggered.  From the diagram I clearly see the rear relay 80 = Rear Relay going into the Body/H loom (R-27) 27 = Fuel Pump plug going into the Body/H loom (T-20) 40 = Short Connector (R-27) I'm reading 12.74V on the blue/black wire which is the power for the Fuel Pump   From this diagram I can see the Ignition relay goes into the front and up to the ignition  2 = Fuel Pump Relay <1M> (R-27) 37 = ING Relay <1M> I started from the pump using this reference Which the way I read it (referencing Nissan wiring color codes) is: Pin Wire Color Function 1 B/P (Black/Pink) Ground 2 L/W (Blue/White)        ECU Trigger 3 SB (Sky Blue) Fuel Pump 5 L/B (Blue/Black) 12V Constant Tested SB to SB on Fuel Pump for continuity - confirmed Tested negative on Fuel Pump to 12V battery and L/B - confirmed 12V Pulled the relay putting 12V between Pin 1 & 2 and testing continuity on Pin 3 & 4 - confirmed relay   So that has me looking at this part of the circuit to understand whats happening here...and im still confused. From best I can tell; the disconnect is back to my previous diagram; between Ignition Relay and Fuel Pump Relay...which yet again; afaik is where the immobiliser should.    Thats what I was trying to explain to GTSboy; im not trying to fix it myself; yet I seem to have to get a Masters in Electrical Engineering (while im busy doing my actual job of DevOps & Cloud Engineering) somehow.  I just wanted more expert opinions; or more so that what I tested is correct and proves it to something around that area; to go back to the alarm tech (for a 3rd time) that he needs to fix it. He keeps telling me its not the alarm. He lives on the complete other side of the city so i understand not wanting to make a trip but as I said before if its the alarm it should be up to him to fix it. But he's adament its not; even though I pointed out the FP was immobilised through the original alarm. To my mind; it seems that the ECU is sending the signal; but the ignition is not getting 12V down the line.       
    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
×
×
  • Create New...