Jump to content
SAU Community

Recommended Posts

guys+ girls, ive got a r31 gtsx with a silver cover rb20det in it and ever since i did this conversion it has had a intermitant surging problem when cold! If i flatten it, it revs up very slowly and then boosts suddenly(goes sideways!) change into second, same thing, third, same etc. after about 3-5 minutes of driving it disapears! wtf is going on?

thanx people

Link to comment
https://www.sau.com.au/forums/topic/15001-surging-rb20det-help-me/
Share on other sites

Flattening it when its cold hmmmmmm..........Not good!!

I think it uses a differant map when cold, which is richer to help get it up to temp quicker. A bit like a choke I think - but correct me if I am wrong. It could be because its running heaps rich, it bogs down a bit then takes of ?

Best bet would be to keep it quiet until its up to temp I reckon

Had a similar problem in my GTS4 - its like someone riding the brakes, right?

My local Nissan dealer told me the timing was retarded to buggery, so I'd suggest you check that first.

and, for crise sake, DON'T boost it when its cold - unless you've got heaps of money to replace the engine..

Guys, it is just the engine warming up, I have exactly the same on my 32 in the morning.

Just don't rev over 2500 for the first 3-5 mins of warm up and you're away!

Boosting when cold is murder on your engine/turbo, like when you put hot water into a frezing glass or vise versa, CRACKS!!! And you don't want to crack your exhaust housing or any other part of your engine...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...