Jump to content
SAU Community

Auto Gauges From Just Jap...

DANSR33

By DANSR33,
in Exterior & Interior Styling

 Share

Recommended Posts

DANSR33 Mentor

DANSR33

Posted
  • Author
Posted
you want some one to install them? or you want knowledge on how to install? i got a boost gauge from just jap , and i have to say its really accurate , and piss easy to install.

I want someone to install them for me...

Its not the boost that Im that worried about.

More the other 2 air fuel and water temp.

sky017 Proficient

sky017

Posted
Posted

dude search the DIY . im sure there is something there , it wouldnt be that hard . there are instructions in the box for sure , try reading them . its not that hard to do . !! . you can find anything on the internet dude .

or if you are that worried about screwing them up , maybe go to a workshop , but then again your gonna be charged a fair bit for a little job

cheers

Allkiller Collaborator

Allkiller

Posted
Posted
when adding the water temp, dont you have to add the sensor between the thermostat and the inlet of the radiator, and not just tap it into the OEM sensor on the thermostat housing, cause it will stop sending a signal to the dash???

True

Yes, some have a dual adaptor for the senders or some kind of sandwich plate.

Dan, any good tuning place should be able to do this easy for you

Yo-Yo Grand Master

Yo-Yo

Posted
Posted

I'd be interested to know How to install them in my factory R34 centre console triple guage cluster.

I too have bought the 3 guage bundle. I got the boost guage, oil temp & A/F ratio.

Anybody here installed guages in the factory R34 cluster or knows where I can get it done?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Replacing Fuel Pressure Regulator

      By Duncan · Posted

      I'm going to slap an old nismo logo sticker on my spare one and sell it to the land of the free for a thousand bucks
    • Duncan
      Replacing Fuel Pressure Regulator

      By Duncan · Posted

      lol, probably should have read further!
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Well - they have arrived.  And they are easy on the eye to put it mildly... These only have three bolts - but for a start there is a key that fits with vacuum like precision..  And as you can see by my ruler, the interface is large..   I listened to a podcast on HP Academy about Dan (KiwiCNC) and I'm more than comfortable he knows what he is doing. R35 Bearing assembly should arrive later today so can mock that up for a look. Can't wait to get these on and get some brake pressure logging too. IMG_3860.MP4
    • GTSBoy
      Nismo GT Pro LSD configurations

      By GTSBoy · Posted

      I would be very confident that they are the same parts (the 2 different SKUs). It seems very clear that you can drop the cam in the 2-way opening, or in the other opening. If you arrange it in the other opening in the same way that you see any other 1-way diff, ie, with the flat of the cam up against the 1° side of the opening, then it would work as a 1-way. It can only spread the ramps when driving forwards - cannot spread the ramps on overrun. It would then appear obvious that if you put the cam into the opening "backwards", that you would get the angled flats of the cam working onto the "points" of the 1° side of the opening, which would give you ramp spread in both loading directions. I do wonder if the forward direction of the 1.5-way config is equivalent to the forward direction of the 2-way, seeing as the cams are flipped and the angled surfaces on those would need to be the same on each side - AND - clearly when installed in either the 2-way or 1-1ay configuration they are not intended to work exactly the same (the ramp angles on the 2-way are 10° different between forward and backward, and the ramp doesn't exist in the 1-way config). 'twere me, I think I would rather actually have a set of rings that offered the 2-way with two different sets of ramp angles, say the 55/45 of the existing design and maybe a 45/37.5 combo for a less aggressive effect), AND another set of rings with a dedicated 1.5-way opening and a dedicated 1-way opening. The 1.5-way opening would actually have the steeper angle on the overdrive side that causes it to be less pushy than the forward drive angle, like you see in many other diffs. But really - if this Nismo thing is thought out properly and all those surfaces work on each other the way that they need to, who am I to argue?
    • GTSBoy
      Nismo GT Pro LSD configurations

      By GTSBoy · Posted

      I would be very confident that they are the same parts (the 2 different SKUs). It seems very clear that you can drop the cam in the 2-way opening, or in the other opening. If you arrange it in the other opening in the same way that you see any other 1-way diff, ie, with the flat of the cam up against the 1° side of the opening, then it would work as a 1-way. It can only spread the ramps when driving forwards - cannot spread the ramps on overrun. It would then appear obvious that if you put the cam into the opening "backwards", that you would get the angled flats of the cam working onto the "points" of the 1° side of the opening, which would give you ramp spread in both loading directions. I do wonder if the forward direction of the 1.5-way config is equivalent to the forward direction of the 2-way, seeing as the cams are flipped and the angled surfaces on those would need to be the same on each side - AND - clearly when installed in either the 2-way or 1-1ay configuration they are not intended to work exactly the same (the ramp angles on the 2-way are 10° different between forward and backward, and the ramp doesn't exist in the 1-way config). 'twere me, I think I would rather actually have a set of rings that offered the 2-way with two different sets of ramp angles, say the 55/45 of the existing design and maybe a 45/37.5 combo for a less aggressive effect), AND another set of rings with a dedicated 1.5-way opening and a dedicated 1-way opening. The 1.5-way opening would actually have the steeper angle on the overdrive side that causes it to be less pushy than the forward drive angle, like you see in many other diffs. But really - if this Nismo thing is thought out properly and all those surfaces work on each other the way that they need to, who am I to argue?
×
×
  • Create New...