Jump to content
SAU Community

Recommended Posts

i have a malpassi running on my rb20.. its the one for when u run over 15psi boost which i am running.. but it has started making a humming noise, sort of vibrating.. it used to do this when you turn the key to ignition.. but i think it was it filling up with fuel... now it makes the noise all the time whenever i put my foot into it... any help would b good.

thanks leigh

Link to comment
https://www.sau.com.au/forums/topic/150998-malpassi-making-funny-noises/
Share on other sites

Mine used to make that noise too. They aren't designed to cop the intial wack from the fuel pump. The diaphrams inside flutter or vibrate with the pulsing of the pump. The fuel pressure gauge I installed at the same time used to bounce around crazy when it made that noise.

The way to fix this is install your old fuel regulator after the fuel rail and then the malpassi then return to tank. (I assume they are the same as RB30ET's). Hook up the vaccum lines to both. The old reg takes the punch from the pump and they both regulate pressure up to a certain psi then the malpassi takes over increasing the fuel pressure at higher boost. Everything smoothed out so much after that and also allowed me to keep a lower base fuel pressure but still run higher than standard boosting pressure to maximise fuel ecconomy.

Mine used to make that noise too. They aren't designed to cop the intial wack from the fuel pump. The diaphrams inside flutter or vibrate with the pulsing of the pump. The fuel pressure gauge I installed at the same time used to bounce around crazy when it made that noise.

The way to fix this is install your old fuel regulator after the fuel rail and then the malpassi then return to tank. (I assume they are the same as RB30ET's). Hook up the vaccum lines to both. The old reg takes the punch from the pump and they both regulate pressure up to a certain psi then the malpassi takes over increasing the fuel pressure at higher boost. Everything smoothed out so much after that and also allowed me to keep a lower base fuel pressure but still run higher than standard boosting pressure to maximise fuel ecconomy.

actually malpassi pumps are very unstable i cant believe you use them when u could get a sard or bosch for the same price...

my 2c

cheers!

actually malpassi pumps are very unstable i cant believe you use them when u could get a sard or bosch for the same price...

my 2c

cheers!

I belive they were talking about the malpassi fpr, not the pump :P

RB30X certainly seems to have a well thought and detailed answer there and I'm wondering if his solution helps out the Malpassi.

I used one for a little while but the noises and fluctuations in pressure bothered me so I sold it.

i am planning on putting a rb25 in my 32 so if it blows that will give me an excuse to do it.. haha

i will put the standard reg on as well and see how it goes.. but i thought that if i were to do that the pressure from the malpassi wold only hold it to the standard reg. and the standard reg would in a way block what the malpassi is doing because it becomes before the malpassi and the fuel rail.. if that makes sense...

i am planning on putting a rb25 in my 32 so if it blows that will give me an excuse to do it.. haha

i will put the standard reg on as well and see how it goes.. but i thought that if i were to do that the pressure from the malpassi wold only hold it to the standard reg. and the standard reg would in a way block what the malpassi is doing because it becomes before the malpassi and the fuel rail.. if that makes sense...

I know what you mean about blocking it but it will only restrict fuel flow back to the tank. Skyline fuel regs are after the fuel rail arn't they??, on the return to the tank, hence pressurising the rail.

Hrrrm, i thought the Malpassi's where the choice, and my SARD was a jap gimmick toy i would cop shit for. This thread could prove me wrong ha.

Agreed though, the SX/Areomotive have a following. I saw dozen of units recently at the 07 SummerNats. Many injected 800hp NA big blocks

Does the fluttering actually cause regulation issues, or is it just freaking ppl out?

M

Malpassi dont get good press inthese forums, but I have seen them used in many top end drag cars so I doubt they are as crap as others make out.

I am aware Malpassi make a few rising rate regulators of differing specifications so one possible problem may be that people are'nt using the correct model. Mine has given me no problems, but I am only putting out 250rwkw not 1000 so I havent needed to upgrade my fuel lines etc

just my 2c

yeah the standard reg is on the end of the rail so fuel comes through the rail then to the reg then to the malpassi (if i put it in after the reg) then back to the fuel tank.

at the moment i have just made an adaptor in place of the standard reg..

it wierd it has only just started making the whining noise when driving lately.. it has always winded on ignition when it fills up with fuel... but it makes me thing that it is starving fuel or something?? i dont know if it is causing damage or not..

No damage.

4door_Sleeper do you have a fuel pressure gauge, if you did i'm sure the needle would bounce around a little bit without you noticing.

lwboosted What sort of fuel pump to you have, mine is a 500hp pump and it never made the noise until a few weeks of having the malpassi in then only makes it once in a blue moon since I installed the standard reg as well. I' almost certain is the arrangment of the rubber diaphram that causes some noise sometimes.

Could you play with hose diameters in front of the reg, to try and remove some the oscillations out the pressure. Do they make automotive fluid "hammer dampeners" Is it possible to replace the diaphragm? All things i would check

M

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...