Jump to content
SAU Community

Recommended Posts

Hi, first post. I'm a 22yr old on my L plates going for for P's soon and I'm wondering which model of skyline I'm allowed to drive.I like these two

http://carpoint.com.au/used-car/NISSAN/SKY...ia/2085965.aspx

http://www.carpoint.com.au/used-car/NISSAN...ictoria/2286926.

The first one is a turbo the second one isn't. Are they both OK for P a plate driver or are they classified as a high powered vechile? :huh: cheers

Ok, thanks alot guys.

Oh, I'm having trouble finding how much klw/hp this car has.hmm.

Not much trouble.

They go by stock figures only.

If your in victoria, the 34 is illegal. If you in nsw, the 34 is illegal.

I think in Vic we go by kw / tonne, something like 130 125kw or there abouts untill the new laws applies in July.

(Just searched, it is 125kw per tonne)

Edited by jimmytim
I think in Vic we go by kw / tonne, something like 130 125kw or there abouts untill the new laws applies in July.

(Just searched, it is 125kw per tonne)

Does it count if you have a couple of sandbags in the boot? :rant:

Does it count if you have a couple of sandbags in the boot? :)

Just put some weights in the boot so it just works out!

(Nah, I think they go by redbook...but then redbook doesn't tell you what the weight of the car is?)

Just put some weights in the boot so it just works out!

(Nah, I think they go by redbook...but then redbook doesn't tell you what the weight of the car is?)

They go by the factory quoted power figure and weight.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...