Jump to content
SAU Community

Recommended Posts

i just bought an alarm

*edit* brand Invincible Super Duper unstealable car security system

details: under car flame thrower function

its a simple shock sensor alarm with all the standard gizmo stuff with remote engine starter

questions:

-how much am i looking at in getting it installed?

-it has central looking system, and looking at my skyline, the central locking only locks the passenger side, not the driver side. is there a way i can work around this or do i have to buy that crap that makes both doors look

-do i have any chance in doing this myself with little electronic knowledge....haha

and yes im poor, i want to find cheapest solution

but it looks like its gonna be expensive

any help appreciated.

Link to comment
https://www.sau.com.au/forums/topic/15202-fitting-alarm/
Share on other sites

for the passenger side you can just get another motor fitted replace the one that is currently in there. These motors arent to expensive but i would buy one through the place you get it fitted at as ive had 2 motors replaced since my alarm installation. I'm happy to say they were covered by warranty. central locking motors are bitches and sometimes break as most of them have plastic cogs

Link to comment
https://www.sau.com.au/forums/topic/15202-fitting-alarm/#findComment-309783
Share on other sites

No probs with mine.. had to adjust it up a couple of times but otherwise fine.

So you have to actually use the key to unlock the drivers side? hmmm, doesn't that spoil the point of a remote immoboliser thingo dingo? I think it can be done by yourself or with some help - the main thing is just to find all the points you need to wire into. If its not skyline specific can be difficult.

Some will require pulling the door trims off, some the steering wheel guard cover, and some stuff routed thru into the engine bay for things like the alarm siren, etc.

This alarm will protect your car well because got a full sensors to protect body, windows and doors (Connected to door switch)

i still luv this engrish! :P

Link to comment
https://www.sau.com.au/forums/topic/15202-fitting-alarm/#findComment-309935
Share on other sites

okay - i would say if there is already an alarm in there its going to have to be removed... then the install, which can take a bit of time with things like remote start.

I would say your looking at around $180 including door motors etc. Just a guess tho. Dont forget most these guys charge by the hour and something like this will take maybe 4hours...

Link to comment
https://www.sau.com.au/forums/topic/15202-fitting-alarm/#findComment-312038
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...