Jump to content
SAU Community

Recommended Posts

Hay guys..

Im wanting to convert my RB20DET to an RB20DE.

As far as I know..

I need:

Headers

New head (?? Can an Rb25DE head fit without hassle?)

ECU (piggy back or new chip?)

pluming for the new intake

Exhaust flange (???)

Anything I missed?

Thanks in advance guys!

Link to comment
https://www.sau.com.au/forums/topic/153697-converting-turbo-to-na/
Share on other sites

Why do you want to N/A a turbo engine....?

Just thought i would ask...

i was holding back on that question also....

people waste money to go forwards not backwards,

it would be a better idea to sell the car and buy a non turbo one?

instead of being down on money you will have money left over or you could even upgrade to a 33 non turbo

Because I dont know what kind of deadshit drove the cars..

At least with this.. I know everything thats happened to it.. I know how well it runs.. I know that everything is in perfect working order and of a high quality.

I would be wasting more time/money in fixong other peoples problems.

Where as with this.. I can spend 1K save more money.. and easly swap it back to turbo further down the track.

well pretty much all you will need im guessing would be, na ecu, na intake pipe, na exhuast headers, and possibly na injectors oh and to fiddle with the timing. otherwise should be pretty easy.

just find out what people need for converting an na to turbo, and reverse it

Your logic makes no sense, however, if you must:

Swap the entire engine over. You can pick up a decent RB25DE for under $1k which will bolt straight up to your existing box & flywheel.

Saves mucking around

I aggree with the above but it doesnt suit your " know everything thats happened to it.. I know how well it runs.. I know that everything is in perfect working order and of a high quality." argument.

Essentially all you need is to remove all the turbo gear, and run some stock headers (or some extractors)

But i would probably take it a bit further than that and revert to N/A Injectors and ECU, also up the compression to something similar to stock whether it be by some shaving/decking and/or NA different pistons - better for fuel economy. Cam etc is the same...

But if i was you.. i would be selling it and buying a second hand RB25, something a little more drivable as an N/A and just as good economy

As stated above it wont be any cheaper. It will drive worse than an NA model due to lower compression. Bite the bullet sell it and buy an NA car. U can get tests done to see if you are buying a healthy car or not. Not everyone thrashes the living daylights out of our cars.

Cheers

Chris

something different :)

u'd be the first to do it

as suggested, sell it and buy a n/a, u'd have money your way, rather than spending it

cant u just get 3rd party insurance

Edited by andz69
  • 3 months later...

how much did it end up costing?

not being rude but u would have made money selling the turbo and buying the n/a....not sure that i would spend money when i could make money....also the car is still in the turbo model so it should still have attracted the higher insurance....what did u end up having to do?

Well.. To all you nay sayers..

Its been completed..

4 Door R32 GTS4 with RB25DE.. and it runs as sweet as.

In your original post you said it was an RB20DET going to RB20DE. My engine knowledge isn't encyclopedic, but the last time I checked pulling the turbocharger off an engine didn't give it another half a litre of displacement.

So you basically did what everyone else told you to do, and got an engine conversion.

I fail to see where you're getting "naysayers" from, since the objections people raised to your idea were for a situation you decided not to go through with.

  • 4 weeks later...

You know what you need bro? A spinning,snapping, turning, twirling flykick to the head... LOL... nah, seriously bro - why the heck would you want to downgrade... ???????? Man... you're nuts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...