Jump to content
SAU Community

Recommended Posts

Platinum,

For my own curiosity, who are you getting to build the motor in Adelaide? :D

Joel, he's getting the guy out at mallala to do it, think his company is allen engineering or something!

I've used stock as I'm only after up to 300rwkw.

Sky30 is running a complete stock bottom end and has been running slightly over 300rwkw for some time now. :D

Also.. With regards to strut tower braces, I was looking at a cusco that very well may do the job.

Edited by Cubes

just wonderin where you guys got your oil pump gasket? Have tried all the usuals like repco, sprints, motormate and supercheap and in all their books it doesn't seem to list them, any help with this would be greatly appreciated.

Had my engine booked in for this friday to get the finishing touches but it looks like i might have to change the dates because i'm having a bit of trouble finding a secondhand series 1 Rb25DET oil pump, Getting the gasket for the oil pump and there's been a bit of a delay with getting my VRS gasket kit for Nissa (Japan) should hopefully be here this Thursday though!

ARGH! :D the drama's of building an engine, fingers crossed it'll all be worth it! :)

What spark plugs r u guys using in your 25/30det combo or what ones would you recommend?

also does anyone have the part number for a SERIES '1' rb25det oil pump or any differing numbers/markings to the series2?

Edited by mr_rbman

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...