Jump to content
SAU Community

Loud Screahing When Engine Is Started

shyr33

By shyr33,
in Engines & Forced Induction

 Share

Recommended Posts

shyr33 Community Regular

shyr33

Posted
Posted

Hey Guys,

There is this loud screaching noise when the car hasnt been started for a few hours or in the morning. Now i know the noise is coming from one of the recently replaced water pump, ac or power steering belts and goes away after a few seconds and stays quiet when im driving. Im thinking the mechanic either didnt tension the belt enough or to much? Or does this usually happen for the first few times with new belts once they are changed. Any feedback is appreciated thanks

femno Grand Master

femno

Posted
Posted

Yeah its a belt. You can also buy a product from CRC i think, its a non slip sticky spray on stuff for belts. But you shouldnt need it. Just tighten them. Thats what i did when i had the exact same prob as you.

shyr33 Community Regular

shyr33

Posted
  • Author
Posted

Thanks for the reply guys, its my regular mechanic so they will no doubt fix it for free i just thought maybe it would go away by itself after a while but looks like ye they didnt tighten it enough.

Thanks again

Duncan Grand Master

Duncan

Posted
Posted

could also be caused by a small person caight in the engine bay. anytime you start the car it hurts so they scream.

That or a loose fan belt....tighten up the alternator adjuster

Taso84 Mentor

Taso84

Posted
Posted

most probable that the belts have been put on too tight. U can adjust the tension in a few minutes with a shifter,

PM me for details on how to do this, I had this problem too when putting new belts on, they usually do it a bit tight to allow for stretching over time

shyr33 Community Regular

shyr33

Posted
  • Author
Posted

Thanks for the feedback guys, i did adjust the alternator adjustment screw a little bit because i thought it was a little loose, then took it back to the mechanics and he said its fine because he didnt want to tighten it to much because it will put to much strain on the water pump and bearing if it was to tight. Maybe some grease or something got onto the belt while it was changed. Ill give it over the weekend to fix itself, if not back to the drawing board on monday i think hrmmm

justin911 Grand Master

justin911

Posted
Posted

ya same, my starter motor used to make a screeching noise only when it was cold. i took her out and slapped some grease in, hasnt done it since.

might even be the starter motor

mine was makn a screachin noise, still havent got it fixed.

  • 4 months later...
Crash. Enthusiast

Crash.

Posted
Posted

hey guys, im having the same issue atm with this. I put some no slip spray on it and this stopped the noise from happening as much, but it only lasted about a week or 2...

can anyone point me in the right direction of what screw i need to tighten, with maybe an image or something? Or where to locate it, any help would be awesome

foznice Veteran

foznice

Posted
Posted

As someone said they stretch over time. So when you first put them on, and adjust them to the right tension, they shoudl be all good, then as they over the next couple of hundred k's, you redadjust them again.

How does grease help the problem? I can see how grease would stop the noise (by lubricating), but I can't see the grease making the belt "grip" the pulley better. Unless it gets absorbed into the rubber over time and moistens it up or something?????? Kind of like, when you drive with wet shoes, it's slippery at first, but after it starts drying out it gets to a REALLY grippy stage....

_x_FiReStOrM_x_ Community Regular

_x_FiReStOrM_x_

Posted
Posted

Avoid using belt grip sprays.. they usually dont do much if anything at all.

If the belt is tensioned enough get a stick of dri-lube, and run it along the belt (carefully!) while the engine is idling until the noise stops.

Even the slightest bit of grease off the mechanics hands, while fitting, is enough to make the belt noisy.

tacker Mentor

tacker

Posted
Posted

If you can twist the belt about 3/4 of a turn is a good place to start and very very small adjustments until it stops making the noise.

Check out what a tight belt will do and i have done a OEM and N1 in the same way.

post-28646-1181502917_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Just_a_datsun
      RB26 block, rb26 head

      By Just_a_datsun · Posted

      Block bump. $400. As above cyl 6 needs bore or sleeve.
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I would think making the argument that the travel is limited by a spring flexing against a spring perch as "the same method". Later on in the document they do state that the spring can't bind on full bump travel and cannot come loose in full rebound travel as well. (which is all very sensible). The laws are actually pretty sensible and reasonable. It's just that the people who enforce and check them don't actually read them or know them accurately. "Oh, coilovers? Instant fail mate. Don't even need to look at it." - Guy who will be instantly reported by me. There is probably merit to people who do get defected for height also get defected for the suspension in that state that allows it. I did never consider the people who are complaining about coilovers being picked on are also running around at 50mm off the floor.
    • Kinkstaah
      Ethanol Content Sensor - Always at 11%?

      By Kinkstaah · Posted

      I think given SAU's knowledge of E85 we can strongly conclude that 10% ethanol in almost any situation is entirely fine. Almost all of the myths against E85 were overblown, let alone E10.
    • The Bogan
      Blue slip

      By The Bogan · Posted

      From your link See bold text, is this referring to damper settings, if so that may a issue for "some" inspectors, I cannot see aftermarket coilovers having the evidence that "must be available that its functional performance is equivalent to the original" Maybe just remove the adjustment knows and hope for the best???? Meh 5.2 Suspension travel In all instances, modifications to a vehicle’s suspension must ensure the integrity of the system and not compromise the ride quality. At least two thirds of the original suspension travel should be maintained in both directions (rebound (i.e. extension) and bump (i.e. compression)), and rebound must be limited by the same method used by the vehicle manufacturer or if this is not practicable due to the nature of the modification, an equivalent method. If an alternative method is used, evidence must be available that its functional performance is equivalent to the original.
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      They actually don't - They adhere to VSB14 rules just like Victoria. The rules are against CABIN adjustable height, and it quite clearly states that the height has to be within parameters. I asked the VASS engineer to confirm this when I got my car engineered and they refused to engineer the coilovers because they didn't meet the requirements for requiring engineering. (mine are height adjustable.) People "Not wanting to bother" with "Actually reading/knowing/adhering to the rules" should result in fines and immediately losing the ability to issue blue slips and/or RWC's in Vic.
×
×
  • Create New...