Jump to content
SAU Community

Recommended Posts

Check out the Group Buy Section... JUST ENGINE MANAGEMENT is offering an Exclusive SAU Offer for a Haltech E11v2 supplied, fitted and tuned for $2850. J.E.M is Australia's leading Haltech supplier. I honestly am not getting anything out of the G.B just trying to help everyone out...

www.justenginemnagement.com

Hitman quoted $3200.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/154619-haltech-ecu/#findComment-2876238
Share on other sites

Tweak it are selling the R33 plug in E11v2 for $2390

EXCLUDING the 3 Bar Map sensor upgrade ($140) and EXCLUDING Fitting & Tune ($450 J.E.M SAU Special)

Total = $2980

J.E.M SAU Group Buy Haltech E11v2 Bonus 3Bar Map sensor (Supply, Fitted & Tuned) - $2850

Regards,

Sarkis

Edited by QRI05E
Link to comment
https://www.sau.com.au/forums/topic/154619-haltech-ecu/#findComment-2876385
Share on other sites

J.E.M Informed me that:

The Haltech E6X is a Piggy-Back Fuel and Ignition ECU. It is not a standalone ECU and does not support sequential injection meaning economy will suffer. The E6X is specifically designed for 4 cylinder applications. Additonally you will need a new harness ($140) to fit on to a RB loom.

However if that unit will suit you, tuning is available at $450 + Installation.

Regards,

Sarkis

Link to comment
https://www.sau.com.au/forums/topic/154619-haltech-ecu/#findComment-2876679
Share on other sites

J.E.M Informed me that:

The Haltech E6X is a Piggy-Back Fuel and Ignition ECU. It is not a standalone ECU and does not support sequential injection meaning economy will suffer. The E6X is specifically designed for 4 cylinder applications. Additonally you will need a new harness ($140) to fit on to a RB loom.

However if that unit will suit you, tuning is available at $450 + Installation.

Regards,

Sarkis

this definatley a NO

Link to comment
https://www.sau.com.au/forums/topic/154619-haltech-ecu/#findComment-2877375
Share on other sites

The E6X can be used as a stand-alone however its idle control and cold start isnt as good as the E11v2 thats why it used as a piggy back... thats what i ment... besides its made for 4 cyl application and isnt sequential injection anyways...

Cheers

Link to comment
https://www.sau.com.au/forums/topic/154619-haltech-ecu/#findComment-2877445
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...