Jump to content
SAU Community

Recommended Posts

Hey guys tonight i had my r34 A/T light come on i turned the car off and back on and it went away, anyone know why it night have happend. It came on when i was driving in d about 10kph and then put it in netural and reved it to about 4rpm thats when i noticed it.

Any reason for it to be on and i dont know whens the last time the oil was changed in the gear box im about to do that this saturday anyway.

THX ALL

Link to comment
https://www.sau.com.au/forums/topic/155542-r34-auto-at-light/
Share on other sites

You could run a diagnostic to be sure, a likely cause is a faulty shift solenoid which ill progressively get worse and finally lock the car in 3rd gear

UM ok how to i fix this solenoid. And dan what were those 2 wholes again so i can run diagnostic and could you please give me those codes again sorry mate to bother u got a new comp all old crap gone lol. Or if you not busy one of these days you could just drop over and have a looksy urself lol, i have a new address now just down the road if intrested ill pm u my new address.

  • 2 months later...
UM ok how to i fix this solenoid. And dan what were those 2 wholes again so i can run diagnostic and could you please give me those codes again sorry mate to bother u got a new comp all old crap gone lol. Or if you not busy one of these days you could just drop over and have a looksy urself lol, i have a new address now just down the road if intrested ill pm u my new address.

Hi AlexR34, I have the same problem too. How did you go with fixing the problem? mine was diagnosed and found the Shift Selenoid B is faulty. Is your too?

ive had mine stick in third before

but it was just after i plugged in the Greddy EMU

so i unplugged it and it went away (it did give a fault code of sorts a/t light flashed 13 times,dont know what that means)

and the the next time i installed the EMU it was fine

wierd things happening

it does come on sometimes if you drive hard in manual mode

but other then that i dont see it much

my bet is it will stuff up the day after my warranty runs out

Would like to know too how to diagnose and change a shift solenoid.

Btw, is it normal when the car is cold that it keeps you from changing to fourth?

I thought that was a normal feature of the skyline electronic autos, that it would lock 4th out until it warmed up?

  • 2 months later...

So how do I get the fault codes from my R34 box, plenty of info about getting it from an R33 box (involving the OD button) which we dont have on R34/S2 Stagea ? Im getting the A/T light flashing approx 6 times sometimes when i start car..

Edited by chook

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...