Jump to content
SAU Community

Suspension Workshop/info Night At Heasmans - Bilstein In Sydney


Recommended Posts

they wont be looking at peoples cars to give specific advice. it's just a general info session. so yeah it doesn't matter if you come by skyline, swift, scooter or skateboard.

ok nice no problems then, hopefully get some info on whats needed for better drifto!

  • Replies 154
  • Created
  • Last Reply

Top Posters In This Topic

ok nice no problems then, hopefully get some info on whats needed for better drifto!

Your hooked on drift.I know you are.When are you going back out next.I want to do one next month if possible after autosalon.Then i think my clutch may be shagged and will need replacing.

BTW i will see yall there tomorrow.

Well I hope all those that came had a good time. I'm glad I took 45 peoples names as we only had about 25 rock up which was a good number.

A massive thanks to the guys at Heasmans. What a great bunch of people to put on a bbq, beers, soft drinks, free hats and calendars and of course lots and lots of invaluable info. I thought I was pretty clued up, but I learnt heaps both from Paul, Doug, and all the guys in fact.

So a big thanks again to all the guys at Heasmans for having us at the shop and showing us some great hospitality.

that's ok, it was shithouse weather, and crazy traffic so I did expect a few drop outs. hence the overbooking. hell, it took me an hour and 20 min to get there in what is usually a 30 min drive!

Well done and a big thank you to the Baron of Beer for hooking this up.

Great people at Heasmans, all the staff were helpful and informative, great hosts.

And all the SAU people, always great to catch-up with you guys.

Oh and "free Hat, free Hat, free Hat, free Hat" :closedeyes:

We had a great night :rolleyes:

Got great information and now I have a better understanding on what goes on with a shock :O

Thanks to Heasman and putting on a excellent night

Thanks Baron for organising a great night :unsure:

Jess

Cheers for organising the info night barron.You were the person with the ARC jacket yeah?

no worries at all. yep, I was the dashing young man in the ARC jacket. lol.




  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...