Jump to content
SAU Community

Recommended Posts

Honestly mate.Why would you want to?

Ive seen plenty of lines with 19 and 20s and they sit a foot off the ground even with superlow springs in it.

Unless its a show car there is no need.Spend your hard earned cash elsewhere.

My 2c

20's would surely offer a harsh ride and make tyre choice difficult? ie:Load rating ect... Maybe coilovers will offset the hight difference and harsh ride mentioned above.

What are the 20's your considering?

I am considering one of two wheels for my Series 2 33. Starcorp Impul rims in staggered set (18 or 19") x 8.5"F and 9.5"R. Or Axis Hiro's in 18 or 19" @ 9.5"F and 10.5"R. Excellent dish with both rims, hopefully 10.5" will fit under rears guards of GTS-T. Anyone have pics of a 33 with these rims on??

Both of the rims I am looking at are listed on tempetyres.com.au site.

i just fitted 19's on my 33 and i reckon 20s would rub on full lock, and possiblly bottom out on a bad pot hole. my cars with spacers and stock suspension. there 9.5 on the rears and 8.5 on the front. shit pic but hopefully can give you some kind of indication of sporting 20s. be sure to post some pics up if ya go ahead

post-35246-1171889207.jpg

Edited by jake33

got 20x8.5s on my r33 gts25t. you need 30 profile tyres otherwise u need to trim a susp arm to make 35 profile tyres not rub.

with the right off set, i had my guards over the rim front and rear with no rubbing.

i had front and rear guards rolled and had my front guard lining removed.

also what other consequences will this cause.

Judging by the responses in this thread (and opinions of non-car people I talk to about big rims) the biggest consequence is that passers-by are going to think you're a tool.

Aside from the ride / handling / rubbing issues already mentioned, I wonder what all that extra weight is going to do your suspension life?

i never had problems. only thing was the ride quality certainly wasnt comparable to a set of 16 x 6.5" stockies...

P.S alot of car people, several from here actually, commented positively on my 20s so i wouldnt be too worried. He has asked if they will fit, not if he should get them, or what others will think about them.

I can tell you now, 20 x 8.5" will fit with rolled guards and 30 profile tyres. just be prepared for camber wear if your susp isnt set up right and your car is lowered as you will find your tyres wear thin very quickly :blush:

thanks guys for the advice. I only asked because a friend was selling some 20" Lenso Rims and probably could have got them for about that price of 19" ( there about 2 months old)

20's would look nicer but i think i will go for some 19's just for a but of ride quality :P

Jake nice Dish :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...