Jump to content
SAU Community

Gtr Low Oil Presure

enzan

By enzan,
in General Maintenance

 Share

Recommended Posts

enzan Explorer

enzan

Posted
Posted

Hey, Just wanted to fill you in on a small problem that I encountered the other day. Cruising along the highway on my way to work I glanced down at my standard GTR oil presure gauge and freaked when I saw that it was just 2kg at 3500rpm. I was stuck at work and left wondering all day about all the possibilities of what could be causing the low oil pressure. I spoke to someone at Advan and was told that the standard GTR sender units give a lot of trouble and can't really be trusted and also that the N1 oil pumps have a habit of breaking the gear. So as soon as work finished I was under the bonnet attemptng to check my oil presure. I disconnected the sender unit wiring plug and noticed a bit of corrosion around the connector terminals. I cleaned off the corrosion, reconnected the sender and started the car, straight away the oil presure shot up to around 3kg at idle!! And at 3500rpm sits around the 6 - 7kg mark. They are fitted with a rubber boot over the sender plug but in my case was not fitted properly, causing the corosion.

Link to comment
https://www.sau.com.au/forums/topic/156526-gtr-low-oil-presure/
Share on other sites
enzan Explorer

enzan

Posted
  • Author
Posted

2kg (no lower) is ok at idle when the engine is at operating temp, but even then as you increase the revs the oil presure should increase too. If yours doesn't move at all then at a guess I'd say that you have a problem with the sender unit. It's located next to the oil filter and is fairly easy to access. Unplug the wiring at the back of the sender, give the terminals a clean with contact cleaner (solvent) and give it a try. If that fails then I'd be checking the oil presure with a workshop type gauge and if that checks out ok, then another sender unit or an aftermarket sender and gauge. :)

  • 2 years later...
Chris_GTR26 Rising Star

Chris_GTR26

Posted
Posted
Hey, Just wanted to fill you in on a small problem that I encountered the other day. Cruising along the highway on my way to work I glanced down at my standard GTR oil presure gauge and freaked when I saw that it was just 2kg at 3500rpm. I was stuck at work and left wondering all day about all the possibilities of what could be causing the low oil pressure. I spoke to someone at Advan and was told that the standard GTR sender units give a lot of trouble and can't really be trusted and also that the N1 oil pumps have a habit of breaking the gear. So as soon as work finished I was under the bonnet attemptng to check my oil presure. I disconnected the sender unit wiring plug and noticed a bit of corrosion around the connector terminals. I cleaned off the corrosion, reconnected the sender and started the car, straight away the oil presure shot up to around 3kg at idle!! And at 3500rpm sits around the 6 - 7kg mark. They are fitted with a rubber boot over the sender plug but in my case was not fitted properly, causing the corosion.

the n1 oil pumps are strong.. its the standard oil pumps that tend to brake the gears

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...