Jump to content
SAU Community

Recommended Posts

Look ive been told to arrange a cruze for 16/2/7 (sat)

we done one last week and it went off, apart for other cruzes going on.....

well it's gona be at 12:04pm at Wellington Pt departing at 12:30, then taking

the back roads of the Redlands to the M1 and all the way to the coast for a few

laps, then to the spit for photo's.

Then link up with another cruze from clubhighrollers, wait till you see 2OWNU

(R32 yellow) lots of cars lots of chicks lots of fun.....

so what do ya say???? will ya come?

Link to comment
https://www.sau.com.au/forums/topic/156620-calling-all-skylines/
Share on other sites

2 parts of the cruze Its time for something a bit different than the usual saturday night local gold coast. Thus Kynee from SunshineCoastCruising.com and I are doing a Sunshine Coast Run this Saturday night! If you're looking to meet some new people and perve on some new and different cars come along for a good night out! :xcited:

Details are as follows.

MEET 1

7pm - 730pm DFO Shopping.

Airport Drive, Brisbane

(Travel 49.24 km,Est. Time 33 mins)

MEET 2

805 - 815pm BP Service Station

Morayfield

(Travel 51.1 km,Est. Time 35 mins)

MEET 3

8:50 - 9.15pm Bunnings,

Caloundra Road, Caloundra.

MEET 4

935pm - 10pm Boat Ramp Car Park,

Parkyn Parade, Mooloolaba.

up date first post dude....

ha ha ha Sat is the First day of Chinese New Year!!

so if you crusie tommorrow you'll be crusing all year... Dont crash tommmorrow or you be crashing all year!!!

oh sorry for going off topic but i would like to swing by if its the DFO meet up...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...