Jump to content
SAU Community

Recommended Posts

hi to all!

well i am an apprentice sheet metal worker im 23 and doing an adult apprenticeship i have been mucking about with metal since i was about 14...here are some of my projects i am making and planning to make

post-28208-1171702477.jpg

post-28208-1171703454.jpg

ok first up i made this air filter adapter out of 1.6mm thickness stainless steel sheet and 75 mm 3" tube...

preperation is the key to tig welding something of this nature can bu "fused " together this is when you apply heat to a concentrated area and the join simply melts together you move on at a steady rate keeping an eye on the moulten pool this is fusing....to have a successful fuse you must have the two edges of material clean and as close as possible if you you try to fuse 2 peices with a small gap it will simply burn away leaving a hole or even bigger gap to fill! and it suxs been down that road.. this is an un pollished part at the moment stainless can be pollished to a number 4 finish using scotch brite scouring pad...this is food grade finish! not that i will be eating off this..high pollishing is possible with the right buff wheels..i found this finish is enuf.

post-28208-1171703605.jpg

post-28208-1171703782.jpg

ok second here is the first oil catch can i made ...it was originally made for my buggy (turbo suburu single seat buggy full custom) but i am using it to mock up the hose arrangement as my car is off the road turbo is at Slides....

ok once again stainless steel used 4 inch tube, 2 end caps, small pipe to fit air filter,

i will add step by step pictures when available monday or tuesday...

but basically this was all fused together bar the inlet pipes where the metal was not touching some filler rod was used (filler rod is stainless steel in a rod form usually 1.5 to 2mm thick sizes vary) you start by "tacking' the end cap on place a tack every 1 cm or so to hold in place securely then lightly dolly /tap with a small hammer to close the gap around the join no gap it what you want.. then proceed to fuse it on you may want to do about a 4 cm long strip then using a wet rag cool the metal by placing the rag directly on it this will prevent the metal from warping due to excessive heat. take your time it will come out better if you do it right! ok thats it for now till pictures arrive

post-28208-1171703884.jpg

post-28208-1171703973.jpg

post-28208-1171704084.jpg

number 3 here is a heat shield i made in around thirty minutes very simple only tool used was grinder tig a press and gilotene

ok i now the press and the gilotene are out of the question for most..but it all can be done with a hammer tig welder gringer and thats about it. same applies for fusing this as stated above preperation is the key!!

if you have the tig to hot or incorrectly sharpened it whill burn unevenly and you want nice even penetration and not to much a that!

i will be adding more and more as i go am currently making an alloy air box here is some other pics just of what is possible with a bit of time and patience!

hope this helps any question just pm me if this isnt detailed enuf let me know can get right down to the nitty gritty!

cheers

soon to be alloy air box..

post-28208-1171705033.jpg

post-28208-1171705160.jpg

bit of time turned this

post-28208-1171705390.jpg

into this: nuthing to special but an improvement

post-28208-1171705589.jpg

post-28208-1171705870.jpg

Link to comment
https://www.sau.com.au/forums/topic/156809-my-fabrication-tips-and-projects/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...