Jump to content
SAU Community

Recommended Posts

  • Replies 153
  • Created
  • Last Reply

Top Posters In This Topic

if it is posted here it is open to anyone :laugh:

The more the merrier...

However in saying that im not telling everyone as i want more than 3 runs and dont want all of Brisbane to show up... >_<

For those who dont know the prices or have not been to willowbank before for one of these events below is some inportnat info...

Cost:

Competitors: $36 to race, admits the driver and one other.

Spectators: $18 adults, $16 students with ID

Children 13 & under are free.

Time:

Saturday Events - Gates open at 4pm and runs commence at 4.30pm, so we want to be there at 3:45pm to ensure a quick entrance and we can start racing straight away before a commodore hits the wall and halts racing for an hour will they clean it up... ;)

To run at these events you need:

Requirements for a car - helmet to Australian Standards, long sleeve shirt, long pants & covered shoes.

Cars can not run quicker than 10.99 sec

so shall we make it sat march 17th then?

This topic is for the 3rd...

Start a new thread for the 17th, if people wanta go on the 17th then they will go on the 17th and like wise with the 3rd they will post here, me personally im going on the 3rd as i have already coxed a mate to run his SS ute and as i said i cant wait to get out there...

This topic is for the 3rd...

Start a new thread for the 17th, if people wanta go on the 17th then they will go on the 17th and like wise with the 3rd they will post here, me personally im going on the 3rd as i have already coxed a mate to run his SS ute and as i said i cant wait to get out there...

Good idea col

Im going on there 3rd because a group of friends are going then

This suxs

I just found out today that work is sending me up north for a week or so from the 1st of march . So I wont even be able to the 3rd my self now god damn it

maybe we might change it to the 17th now becuase I might give people more time as well

What do you think ??

What do you think ??

As I said to Warren, no reason why we cant go to both...

Im still going for the 3rd reguardless as im tto keen to get some numbers on paper... :P

But as i said in the 17th of March thread, ill probablly coax Nay to take the S15 so ill be there anyway...

hi all. ill be in for this.. on the 3rd. but i need to borrow a helmet or two.

dont think ill drive my GTR.. hasnt seen a track yet and she dnt need to.

will run my mates S14a and maybe the R34.. yay auto...

so if someone could lend a few helmets then im in :blush:

try cash converters.. you will be surprised

last time i went in they had some good nam helmets at cheap prices

as long as you check that its not cracked or doesn't look like its hit the ground before you're laughing

I did the cash converter thing and the cheapest lid they had was 150 bucks. robbin bastards. :happy:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...