Jump to content
SAU Community

Next 12 months

NismoGirl
 Share

Recommended Posts

NismoGirl Grand Master

NismoGirl

Posted
Posted

A few people have commented to me that in the next 12 months the prices of imports (good condition ones) is going to rise quite dramatically because of the current import laws.

I know you can't really predict whats going to happen. If it happens it happens.

I reckon it could well happen. It would be nice anyway :)

What do you's think? Have you heard any of the same rumours?

Link to comment
https://www.sau.com.au/forums/topic/15699-next-12-months/
Share on other sites
predator Grand Master

predator

Posted
Posted

I've heard bits of both "prices will rice" and "prices will stay the same" for both importers and other people i've spoke to..

If anything, just lately i've noticed prices on most cars are cheaper than before ever before.

Personally, i think prices will pretty much follow the usual downward trend and everything will level out by the end of the year. Modified ones might attract a bit of a premium but otherwise much will same.. new models will come out, old ones will get cheaper, etc.

Link to comment
https://www.sau.com.au/forums/topic/15699-next-12-months/#findComment-321110
Share on other sites
franks Veteran

franks

Posted
Posted

price comes down to supply vs demand. its a simple equation that could have many different factors effecting it.

the price of imports decreasing, holding or rising will, i believe, depend on many varied things...

- the local market is starting to get interesting with the turbo xr6 and new monaro's then you have the locally delivered sti's, evo8, rx8, 350z's ...

- cost of insurance for imports (and any performance car for that matter) has been and is getting ridiculous

- cost of compliance and the amount of compliance workshops. i believe for a workshop to compliance a vehicle it costs a bomb now.

Link to comment
https://www.sau.com.au/forums/topic/15699-next-12-months/#findComment-321908
Share on other sites
Champinco Community Regular

Champinco

Posted
Posted

well ive heard that these new imported laws are a way to "weed out" all the dodgy ppl doin imports. like franks above says the cost of compliance will rise. this is because to get an imported car complianced ie: skyline (or whenever the date will be/is") u will have to go to a certified complianced business. and there aren't too many of these business floating around. to become a certified complianced business u will need a proper workshop along with all the neccessary equipment fit for servicing, altering etc.... Now the reason why this will weed out the dodgy ppl gettting compliances is because to become this so called registered business you will need someone from canberra to come down to inspect it. I think this costs A LOT of money.

It is my belief that the actual cars wont appreciate in value but follow the spiral trend of depreciation. Again as franks said it depends on a whole bunch of factors. However the prices for getting these plates will soon solely depend on these registered imported business-and that is a problem cause if there aint too many around and there is a demand for jap imports then they can charge a shit load. I predict that this wont happen until a couple of years time cause there are heaps of current jap imported cars in australia (ie: the ones that we drive now)

Hope this all made sense and i hope im correct.

not sure.

ta ta

Link to comment
https://www.sau.com.au/forums/topic/15699-next-12-months/#findComment-321921
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      All I hear is ROADTRIP!
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...