Jump to content
SAU Community

Recommended Posts

i say flog the f**k out of it

u c u cant always sit on different rpm's in full autos either so where does that make any sense about running it in?

give it stick he says, give it stick

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

supposed to run the new car at various speed & gears.

just like when you get a gearbox rebuild.... going through each gears to run it in, especially the first 500km.

I tell you now its all wrong :(

So why post contrary to that then... oh... i get it. A litle bit of sarcasm.

Damn i should have noticed that sooner...

Well, go do some research if you dont wanna listen to someone that has :)

Some Manufacturers use Mobil 1 synthetic right out of the box, dont even use the "mineral for 100kms" etc etc.

Why you might ask? Because they have all realised that it doesnt make a difference with the motors of today :)

I have Castrol Edge 10-60 Fully Synth waiting to be dropped into my motor. Bed the rings on the dyno (less than 20mins) and wind up the wick.

So Joel, the point... go hard just like in Shepp :)

hey great choice of a car dude as my old man has one to him self and the compairment to the skyline coupe with hicas is that i believe its quicker then the gtst but not faster and the skyline handle faster speed around corners than the Mazda 3 SP23 but the mazda is a much more relible car to drive , verry nice. cheers

So it can hold 6 Latte's :)

Perfect for those hairdressers conventions.!

Ha ha Mr DECA winner

Lets see how funny it is when my 3 hands ur cheater wrx its arse to it at DECA ???

Then again maybe not :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...