Jump to content
SAU Community

Recommended Posts

I own a R32 GTSt and have found something very interesting with the brakes.

I wanted to change the rotors so ordered in some R32 GTSt disc rotors: A 280mm diameter, 30mm thick disc rotor (for the front). These are the factory spec - and can be found in the DBA catalouge.

When I took the rotors of my factory R32 GTSt I found that the rotors were 280mm diameter, 22mm thick.:(

The 30mm rotors would not fit into the callipers!:)

Is anybody aware of any R32 GTSt’s that came out of the factory with smaller brakes? (280 x 22)

Would normal R32 GTSt callipers and rotors fit on this model?

Would R32 GTR Brembo’s bolt straight on as well?

I would appreciate any assistance, even if only to point my in the correct direction of where to find this information.

Link to comment
https://www.sau.com.au/forums/topic/15749-weird-r32-gtst-factory-brake-options/
Share on other sites

I've done a bit more research and it seems that the 4 pot calipers were an optional extra (technically standard on an M spec) - but could still be optioned out.

The single pistoned caliper is the same as a S13 200SX brake.

I checked my model spec KRCR32RGFSM AA - which is defintely a 5 spd manual M spec GTSt (don't know what the AA stands for) - so my only guess it was optioned out - or changed over before it landed in Oz

Means with a bit of modding (ripping off the dust covers) a GTR brake will fit under there nicely.

If anyone hears more about factory options - I'm still interested

Thanks,

Do you have standard rims? Remember the 4 pot's stick out alot more and require different offset rims. If you have aftermarket ones theres no quarantee they will fit.

Just something else to think about if you didnt already have enough. By the way the 4 pots are commonly bolted onto S13 silvias and 180SX's so theres no problems bolting them up. Clearance is the main issue.

Red17

PS: I though the M Spec was HCR32, not KRCR32?

Yeah the type is E-HCR32, where E stands for petrol, and HCR32 is the model type.

I've posted another thread about decrypting the VIN plate (which my other research project - related to determine why I have such pissy brakes)

Might check out the availability of 4 pots on Silvia's - almost all have 4 stud wheels which means the rotors wont go on my 5 stud hubs.

The car if defintely M spec from the model spec, but also it has a std GTSt steering wheel, not the snazzy M spec wheel. So it seems the car is a factory M spec with a couple of downgraded options.

Maybe the original buyer didn't quite have enough money, and had to deoption the car.....maybe I'll never find out.

Thanks for the caliper tip though, I'll let you know what I find out

KRCR32RGFSM AA

RC = rwd, R = M spec, 32 =R32, GF=manual (that's about all that is confirmed at this point)

An offer worth considering.....

Would that full set of GTSt brakes come with a master cylinder as well.

I have a bad feeling if I upgrade my calipers, that I will also have to upgrade my master cylinder.

I will try to work out this week what the part number for the big brake master cylinder is, and if that is what I already have installed in my car.

I've got a hunch though that I will have a much smaller master cylinder (to go with my 180SX size brakes).

Thanks for the offer though Dragan, I wont keep you hanging too long.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...