Jump to content
SAU Community

Recommended Posts

Ok..

couple of months back i started a topic which was about a similar issue, where under 50%+ acceleration i'd be getting popping outta the exhaust and felt like someone was pulling on the handbreak.

But this time, no popping noise.. its just accelerates, and around 4krpm it just dies in the ass till it gets past then continues to accelerate.

last time a ECU reset solved the issue, I've recently installed a SAFC (after this issue started) its untuned, but no fuel adjustments have been made, would this be doing it?

anyway im going to try and get a quick dynognosis tomorrow when i pick the car back up =)

just wondering if anyone can point me in the right direction to save $$$ on dyno time.

any way to turn R&R off completely

thanks.

Edited by illusiVe
Link to comment
https://www.sau.com.au/forums/topic/158382-r34-gtt-think-its-rnr-now-dammit/
Share on other sites

safc willl help as you will be able to alter the fueling around those cells that are going into rnr

but it will not eliminate it entirely , like all safc operations it will be a bit of a juggling match

remap/full ecu is your only true solution

My R34 gtt did the exactly the same thing even on the dyno it would drop out mid range and then pick back up.

Firstly do ou still have the factory turbo??? If you do then that is your problem (it has nouthing to do with the computer) The nylon inpellar probally has cracks in it or even chips off it.

fixed it..

stupid guys who worked on my car needed to get to the suspension and for some reason ripped my boost controller.. so it wasnt plugged in, and when the 12v came in it grounded the engine, causing loss of power.

rewired and problem gone... for now :O

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...