Jump to content
SAU Community

Recommended Posts

FMIC don't really give power.

Is your POD exposed or boxed up(enclosed)? If its exposed your probably losing power right here compared to a standard airbox because of the heat from the engine bay.

Power isn't everything take your car to the drag strip and see how it performs against other cars with the same or more power.

Its ONLY A dyno reading, its used for tuning get your powerfc in wack in more boost and tune it and you will get the results or thereabouts.

Just get the power fc in it, the stendard r&r is far more severe on the r34 than the r33. I dyno'd a stock r 34 gtt, then he went away and got a million dollar front mount, million dollar exhaust, and brought it back, gained 4 rwkw, and lost about 30 kw in the midrange. looked like a rollercoaster. How does your dyno graph look?This one had 2 or 3 skijumps instead of the usual one for a r33)

for 33's i disagree, I've heard people say 12psi through 33's stndard cooler but with my own s2 i found that bloody unlikely as mine was majorly miss behaving with the standard smic.

drop a free'ER flowing fmic and piping and walla...she stoped nock,backfiring an just drove like a frign dream.. after that.

I get a jjr split front an dump, this weekend, im putting in my widebody 3" catco with it on my 3" cat back and il let you all know what she's like @ 10psi

the stock maps scale up when inc boost, so is it a rising rate when inc boost so the car literally runs worse afr;s or they come down a bit ?

The afr's get heaps worse when upping the boost, even standard they can go off the scale(<10:1), and it just gets worse from there, the other major problem is that the computer pulls out heaps of timing which loses any powe gain you would have had.

184rwkw @ 9psi with boost dropping hard (midrange was at 13psi)

FMIC, Pod

Zorst with terrible cat (changed now, goes better)

Avcr (hate it)

Power FC

Somehow want to hold 14psi and make 200rwkw, we'll see if i can sort the boost dropping issues out.

Edited by jazza08
for 33's i disagree, I've heard people say 12psi through 33's stndard cooler but with my own s2 i found that bloody unlikely as mine was majorly miss behaving with the standard smic.

drop a free'ER flowing fmic and piping and walla...she stoped nock,backfiring an just drove like a frign dream.. after that.

I get a jjr split front an dump, this weekend, im putting in my widebody 3" catco with it on my 3" cat back and il let you all know what she's like @ 10psi

the stock maps scale up when inc boost, so is it a rising rate when inc boost so the car literally runs worse afr;s or they come down a bit ?

This is an r34 thread so this post is completely irrelevant and will only serve to confuse people who don't read carefully.

FMIC in r34's rare give any power. This much is true.

Dyno's do give very different read outs and are not comparable without controlled circumstances. For instnace, I went to Bel garage Mainline dyno one day and got 255rwkw, a month later on a similar day weather wise, with no other changes, I got 256rwkw on the Dyno Dynamics dyno at UAS.

Now if I went to Bel and got 255rwkw and you went to UAs and got 255rwkw I would not expect that they would have identical power until both cars had been on the other dynos.

ps. I now have 272rwkw on Unigroup's Dyno Dynamics dyno but got over 300rwkw on another dyno.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...