Jump to content
SAU Community

Recommended Posts

Skyline R32 gtr Bayside Blue wrecking, with aftermarket parts

Link for 2nd Bayside Blue Gtr - http://www.skylinesaustralia.com/forums/in...howtopic=163239

*Also have a Saas racing seat (not from this car) $200

*Aftermarket mirrors available again $150 (one mirror is missing the glass)

*R33 gts-t tail light $100

*R32 RHS headlight $60

Will post small items interstate.

PM with any Q's or email [email protected]

Located in greensborough, Melbourne 30mins N.E. the city

Mob 0417 125 253 Elliot, PLZ CALL AFTER 4pm During week days as i can't answer calls during work, Any time wkd's.

Edited by KLR32
  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

*ARC FMIC 600X300mmX80mm i think, in fair/ok con'd $300

does this have any piping? how much posted to sydney 2170?more pics to [email protected] plz cheers

why are you wrecking? has the car been crashed..

Wrecking as it has a bit of rust in the rear quarters and boot, have a 2nd bayside blue r32 GTR i am pick up mid this week, so there will be more parts available.

I will try and get the cooler off tonight, had a busy wkd so im replying to all PM's atm, also i have a 2nd r32gtr i am picking up this week which i will be stripping too!

I will get some more pics up tonight too!

dayms...im after a muffler/cannon lol let me know if you wanna sell one of yours. also if you have any oil temp+pressure+water temp gauges...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...