Jump to content
SAU Community

Recommended Posts

  • Replies 490
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Allright, Group buy 10 is rolling, I have 3 confirmed orders:

- Fry_33 for R33 Gts-t front/rear

- dan.1337 for R32 Gts-t front

- djr81 for R32 GTR front/rear

Group buy 10 ending this Friday 25th May - so don't miss out!

Would it cost any more to have them drilled 4 and 5 stud PCD 114.3

Looking at r33 fronts and s14/s15 fronts in both varients.

Price for per pair delivered to perth 6027

Cheers

price please for r33 gtst front and rear, slotted. just want to know when will full payment be needed by so i can pull my finger out and get some new rotors

cheers eli

edit: also need postage to capalaba qld 4157

Edited by ELI
Would it cost any more to have them drilled 4 and 5 stud PCD 114.3

Looking at r33 fronts and s14/s15 fronts in both varients.

Price for per pair delivered to perth 6027

Cheers

YES it will. You will need to purchase one whole crate of 120 pieces of rotors. That cost a lot!

Sorry, no custom drilled allowed.

Would it cost any more to have them drilled 4 and 5 stud PCD 114.3

Looking at r33 fronts and s14/s15 fronts in both varients.

Price for per pair delivered to perth 6027

Cheers

Would i be able to get prices (delivered per pair) for the r33 fronts and s14/s15 fronts in both varients to perth 6027.

Thanks

n i'll just get them drilled 4 stud locally :)

I'm in and paid up for the R33 GTST Rotors F&R

Thanks Rianto

No problems, your payment has cleared...

Will organise all the orders this Friday...

Updated order list:

- Fry_33 for R33 Gts-t front/rear

- dan.1337 for R32 Gts-t front

- djr81 for R32 GTR front/rear

- k3 for S14 front/rear

Two more orders in tonight:

- SoFly for R32 Gtst front

- fluent for S13 2.0 front.

We have 6 people I will organise to submit this group buy tonight...

Can you also get group buy prices for EBC brake pads?

Looking into R32 gtst grooved/slotted rotors (front) + EBC greenstuff (front & rear)

Possible to get a cheap bundle price for the above setup?

As my pads are worn out and my rotors are undersized :stupid:

Thanks

Patrick

Hi mate, prices for front + rear rotors for the GT-T please. In both slotted and slotted+dimple version please.

I know you said theres no 310mm but would the 296mm for the R33 GTS-T fit the GTT fine?

Thanks,

Andy

Edited by Andi
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...