Jump to content
SAU Community

Recommended Posts

Hi guys,

I got new tyres this morning, all the same dimensions around, so no ATTESA issues.

4 wheel computer alignment. All 4 wheels balanced.

Here is the problem:

Steering wheel seems to sit slightly down on the right side (ie. right side down), not by much, but enough to notice. Above about 80-85 the steering shakes noticeably too. Worse than when I had shitty tyres on front!

I will be taking it back, but after some pointers/ideas. I have 5mm spaces on the wheels. 235/45/17 all around. I took it to a well known tyre place in Melbourne that deals with heaps of imports and high end cars, never heard a bad thing about them. When i noticed this i dropped into a Bob Jane (not where i got the original job done) and asked them to check it over. They said all looked ok, no obvious stuff-ups. Balanced ok and tyres fitted correctly.

Please help with any advice/ideas you have!

Cheers,

Dan :D

Edited by JonesyGTR
Link to comment
https://www.sau.com.au/forums/topic/158922-r32-gtr-tyres/
Share on other sites

Steering wheel not centered when driving straight is usually the alignment place adjusted your toe settings without centering your steering wheel...

The shaking of the steering wheel when going above 80 sounds like a bad balance - maybe some weights came off?

You could also try removing the spacers to make sure they aren't causing any issue, a lot of balancing/alignment places don't like them, because they can cause issues like your seeing :unsure:

Otherwise, take it back i guess? Get them to take it for a drive and show them the issue...

Link to comment
https://www.sau.com.au/forums/topic/158922-r32-gtr-tyres/#findComment-2955964
Share on other sites

Most modern wheels centre on the hub itself, not on the studs. The probability is that the spacers are preventing the wheel centring properly. This is where the "imbalance" above 80-85 k is probably coming from.

And make sure they centre the steering wheel and align to that.

Link to comment
https://www.sau.com.au/forums/topic/158922-r32-gtr-tyres/#findComment-2956564
Share on other sites

Most modern wheels centre on the hub itself, not on the studs. The probability is that the spacers are preventing the wheel centring properly. This is where the "imbalance" above 80-85 k is probably coming from.

In that case all you need to do is jack the car up and back off all the wheel nuts and retighten progressively in a star pattern to center it properly. Done and done.

Shit, if i can fit non hubcentric wheels without steering shudder issues, anyone can. The wheel nuts are conical for a reason people, it's so they match the cone shaped indent in the wheel and center themselves.

Start semi related rant:

Just on a side note; has anyone else noticed the number of people jumping on the hubcentric band wagon in the last year or so? About 1 in 4 sets of aftermarket rims i see on skylines and silvias match the nissan hub, no balance issues. The majority of jap bolt on spacers don't have the hub on the outside, mine do and were a press fit. From a purely functional point of view, is any one really dumb enough to believe that if you can slip the wheel over the 10mm long knob on the hub (we're not talking press fit here) that the studs won't be taking the load?

End rant....

Link to comment
https://www.sau.com.au/forums/topic/158922-r32-gtr-tyres/#findComment-2962564
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...