Jump to content
SAU Community

Noise At Lowish Revs, Light Load, 2nd + 3rd Gear

timheather

By timheather,
in Engines & Forced Induction

 Share

Recommended Posts

timheather Collaborator

timheather

Posted
Posted

Hey guys,

Hope someone can help with a noise that's recently started up... Sort of a "zzzzz" noise, seems to be in second and third gears mostly (maybe just can't hear it at higher speed), but I think I've heard it in 1st before as well. Was thinking turbo, as odo reads 216000km and I've had it since 14000 without replacing it. No oil in the inlet pipes however... Definately seems to be coming from under the bonnet as I can't hear it with the windows up. Doesn't do it free reving. Seems to do it only when warmed up. When it starts making the noise, it goes away immediately as I accelerate.... haven't been booting it too hard since it started though... Please, has anyone got any ideas or tests I could carry out (short of removing the turbo, yet).... :(

SLIPPERY Experienced

SLIPPERY

Posted
Posted

Ive got the same noise In my GTR and had it on my gts-t. The noise comes from the gearbox and ive just put it down to my rattly old twin plate

you only get it at low engine speeds right?

timheather Collaborator

timheather

Posted
  • Author
Posted

Only prob is I don't have a twin plate... stock rb20det with unknown clutch... been in for the 75000km I've owned the car. I thought it might have been the gearbox too, but I can hear the box throught the trans tunnel and it doesn't seem to be coming from there... tried some nulon g70 in it to see if it would help but no change... only started less than 1000ks ago...

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • GTSBoy
      Another "where do these lines and plugs go" RB25DET question

      By GTSBoy · Posted

      4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • GTSBoy
      R34 GTR Seats / No longer reclining

      By GTSBoy · Posted

      Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...