Jump to content
SAU Community

Recommended Posts

AS the topic states.

Anyone who did a comp test on their stock R33 before they modded it post it up.

I did mine recently before I threw on some mods. all mine had was the HKS from the turbo back with SuperDragger Exhaust. running stock boost etc. etc.

I got 175-175-175-175-175-175 all pots , I was definently pleased with that they were nice and even.

When I was chatting with a GTR owner recently he seemed to think that was incorrect. Or that my internals are not stock for that compression test.

So went back to my mates shop did another same result. Now he uses top quality snap-on equipment so I'm sure all the readings are correct.

Just wanted to do a Comparison to anyone elses results.

Link to comment
https://www.sau.com.au/forums/topic/159442-compression-test-results/
Share on other sites

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Mine got 175 with the throttle wide open, 160 with throttle closed r32GTR

8.5:1 compression RB26DETT

9.2:1 or something on RB25DET

So either you did test with throttle closed or you have a lower static comp ratio?

who are you talking about. ME. i did it with throttle closed i think. Humm will do again tonight. But the range is 1.2 MPa which is 175pis, that is NEW from facotry. Limmit is 0.9 MPa, so that is 130 Psi with 0.1 MPa differance between. So still sweet. My engine has done 80K so expect lower compresion.

BTW mine is for an R33 GTST 95 series

Thanks for the heads up GTRsean. Not sure if it was open or closed. all i know was car was off :ninja:

ill be doin another very soon, keen to check out if theres been any change since ive been driving around on 11psi for 2 months.

-cheers.

Videospace, were they done with throttle open?

And did oil get put in cyl to see if it was piston, rings etc?

32gtr rb26dett limits from memory are:

171 new

160 avg

125 limit

no more than 14psi variance,(146,160)

Yep. Idle is crap. When it is cold it misses a lot. When it is warm its very hard to tell there is anything wrong. The idle is still not brilliant when it is warm but otherwise the power is OK and everything else.

Bryce

And yes the 6th cylinder was 150 too (sorry guys).

And yes we did try a "wet test" with a t-spoon of oil and the compression improved. Rings it is. Rebuild away! I am considering a swap with a R33 RB26.

so this test is around $70 and most car garages can do it? or do you need to go to a special place? Keen to see how my engine is doing. Might do one of those leak down tests too, someone mentioned above.

oh well vidospace, now you can build whatever engine you want.

N1 block ftw!! :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...