Jump to content
SAU Community

Recommended Posts

Possibly due to the getrag box???

I'm not sure,I was going to reco a 33 gtr twin plate for my 34, but I don't want to waste my time.

Not the same Rick. Get a Nismo coppermix twin mate you will be very happy with it, I know they are pricey.

So you have to change the flywheel when you even get a single plate if the flywheel needs machining at all? And does that mean that a 33 GTR twin which comes with its own flywheel is ok?

Rick I think you will find the spline on the shaft is different so the 33GTR clutch is no good to you .

R34 GTR flywheels are dual mass ( 2 piece ) just like subaru liberty .

I agree with that and the latest coppermix is even better.

I spoke at length with wrxhoon and others before deciding that for the mainly commuting and road driving (vs drags or track work), i was better with a single which Jim Berry built for me with uprated pressure plate, and new single mass flywheel. It was obviously cheaper, but was even lighter clutch action and a dream to use on my daily sydney commute. I am really happy, I know wrxhoon is happy with his coppermix, and others will be with theirs, so its probably about application 1st, then decide on the best clutch brand material etc etc.

Cheers

Ned

I spoke to Jim berry and he does go for the single, but at $1800 with flywheel I believe I could get a nengun nismo twin in...unless I can find a better value single which sounds like it needs a flywheel anyway, I might just have to keep saving.

are the nismo twin plates noisy at all? just wondering because a mate of mine has a F6 with a $4000 twin plate from over east which is meant to handle 1000rwhp but at idle its pretty damn noisy. His clutch is very hardcore, but i wouldnt want a clutch in daily driver that was making rattles and what not.

are the nismo twin plates noisy at all? just wondering because a mate of mine has a F6 with a $4000 twin plate from over east which is meant to handle 1000rwhp but at idle its pretty damn noisy. His clutch is very hardcore, but i wouldnt want a clutch in daily driver that was making rattles and what not.

thats most likely to be the gearbox not the clutch if it goes away with the clutch pedal depressed.

its normal for a bit of noise in the gearbox when idleing. put the foot on the clutch and it should go away though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...